HPH RK3288 ROM v1.2 by mo123 (20141117)

[fmoreira66]

Re: HPH RK3288 ROM v1.0 by mo123 (20141026)

Can't mix the system.img with other ROM's, it won't boot.
You can use the boot.img and resource.img from another ROM/device that is from end Oct or November and it should work.

Hi mo123, if I understood correctly you are saying that I should take your entire ROM and just substitute the boot.img and resource.img with the ones comming with the latest Nagrace HPH firmware 1.3.35, correct? And what about parameters? Should I use the 4Gb Userdata from Nagrace HPH firmware 1.3.35 or does not matter?
How can I check that I do not have a corrupted version of your ROM?
I will download it again just to have a fresh start.
Thanks.

[mo123]

Thank you. Does this mean I just have to keep both the options unchecked? Which is already the case, options are unchecked.
Or should I do differently, backup or else....

No, you should flash everything as in the instruction picture in the OP.
Replace my resource.img with your ROM's resource.img or don't.
It it still gives problems, also use your boot.img instead of mine.
The partition sizes are different so you should flash all the images otherwise it won't boot.
The Ugoos UT3 ROM on their site might be too old. - http://ugoos.net/index.php?route=pro...download_id=55

[Hocine.Merouane]

Just flashed the ROM on a 32GB box and it worked perfect.

Try also to use the boot.img and resource.img from the Ugoos UT3 instead of this ROM.
But it must be from a new ROM end October or November.
Upload the resource and boot.img from the latest Ugoos ROM and I'll tr to make a new kernel for Ugoos UT3. Just also post the ROM version, date.

Thank you. Does this mean I just have to keep both the options unchecked? Which is already the case, options are unchecked.
Or should I do differently, backup or else....

[mo123]

Hi mo123, tonight I've flashed my box more than 10 times trying to install your new ROM, but without success. I've tryed to install your full ROM and only use the resource.img of 1.3.35. To use all .img fom 1.3.35 and only use your system.img . And many more combinations in the middle. All without success. After the successful flashing in every attempt I've got the green man and then after the automatic reboot the grey man appear without any line flowing beneath and I've waited more than 15mins in every attempt but nothing happen until I've reflashed the full 1.3.35 back again and start over again.
Your previous version I was able to flash it without any problems before when you've released it, by keeping resource.img, kernel.img, boot.img and parameters of Nagrace firmware for my box. But this time that combination among all the others didn't work either. Just replacing the system.img from 1.3.35 with yours and flashing the latest firmware version from Nagrace for my box also had the same result. So it seems that the problem is in system.img . Does anybody with a 4 Gb of RAM and 32 Gb of storage Nagrace HPH RK3288 successfully installed the latest ROM from mo123?
I really would like to install your new ROM mo123. :-(
Thanks.

Can't mix the system.img with other ROM's, it won't boot.
You can use the boot.img and resource.img from another ROM/device that is from end Oct or November and it should work.

[mo123]

Just flashed the ROM on a 32GB box and it worked perfect.

Steps
1. Had a working ROM already from October.
2. Choose 'Lowerformat' in first tab at the bottom.
3. Choose 'run'.
4. Wait 5 minutes before unplugging device.
5. Bootanimation plays and after 20 seconds ROM boots to Homescreen.

Use a USB port from the back of PC.
Reinstall the drivers.
Using Win 8, 32bit

Try also to use the boot.img and resource.img from the Ugoos UT3 instead of this ROM.
But it must be from a new ROM end October or November.
Upload the resource and boot.img from the latest Ugoos ROM and I'll try to make a new kernel for Ugoos UT3. Just also post the ROM version, date.

[Hocine.Merouane]

Have not seen last reply from fmoreira66 !

same problem of boot process: green and grey Android logo guy.

[Hocine.Merouane]

Please help

Hello

I have just received my UGOOS UT3 4G/32G and after some tests, found the video quality was not perfect.

So, I decided to search and test a new firmware to see for a difference until I found you.

I have tried to apply yours but it did not work.

Could someone please guide me with a real step-by-step procedure?
For example, after the flash is finished, should I unplug the power cable?
The first boot was showing a blank Android logo for more than 15 minutes, then I deciided to re-flash with the original firmware.

Thanks a million in advance.

PS: @m1pnk --> you have the same device, so maybe you could personally help me?

[fmoreira66]

Hi mo123, tonight I've flashed my box more than 10 times trying to install your new ROM, but without success. I've tryed to install your full ROM and only use the resource.img of 1.3.35. To use all .img fom 1.3.35 and only use your system.img . And many more combinations in the middle. All without success. After the successful flashing in every attempt I've got the green man and then after the automatic reboot the grey man appear without any line flowing beneath and I've waited more than 15mins in every attempt but nothing happen until I've reflashed the full 1.3.35 back again and start over again.
Your previous version I was able to flash it without any problems before when you've released it, by keeping resource.img, kernel.img, boot.img and parameters of Nagrace firmware for my box. But this time that combination among all the others didn't work either. Just replacing the system.img from 1.3.35 with yours and flashing the latest firmware version from Nagrace for my box also had the same result. So it seems that the problem is in system.img . Does anybody with a 4 Gb of RAM and 32 Gb of storage Nagrace HPH RK3288 successfully installed the latest ROM from mo123?
I really would like to install your new ROM mo123. :-(
Thanks.

[mo123]

Hi mo123,
First off all I would like to say thank for all your hard work for the RK3288 community in general and for Nagrace HPH TV Box in particular.
Regarding your new ROM, do you think I can flash it fully in my HPH RK3288 with 4Gb of RAM and 32Gb of Storage?
Or I must keep my resource.img from my current 1.3.35 Nagrace firmware?
Thanks in advance for your support.
Keep up the good work.

Can flash the full ROM.
Remember to do a lowerformat since the partition sizes are different, an upgrade on the second tab won't work. Have to flash from the first tab.
Works on both 16GB & 32GB Models and Ugoos UT3 boxes(with their resource.img)

[mo123]

Okey, thank you. Can I try with the boot.img and resource.img included in your ROM first? Or do I risk to brick my TV box then?

You can try the full ROM first.
These boxes are mostly unbrickable, if it doesn't work just reflash.
You have to do a lowerformat first since the partition sizes are different than in previous ROMS.

[fmoreira66]

Re: HPH RK3288 ROM v1.0 by mo123 (20141026)

Yes, Nagrace is one of Rockchips best suppliers.
They were the first company to actually release a RK3288 TV Box before anyone else and their box is more stable,faster than boxes that are made recently.


My new ROM is now uploaded for everyone to try.

I'm limited by space(800MB in Windows, if I go over 1GB in Linux the ROM doesn't boot for system.img) to not install more apps automatically, will try to find a solution or wait for TWRP/CWM for RK3288 TV Boxes that will make it much easier.

There are 2 bootanimations, just rename bootanimation.zip.old to bootanimation.zip with root access to see the other one.

First boot takes a while but second boot is less than 20 seconds.

Includes latest SPMC v13.3.4 beta 1 from today(not released on Play Store, only on Freaktab) that has perfect video playback and can F/F, R/W & seek with no crashes. Also plays lots of avc/mkv files that have black screens with Kodi beta 2/3.

Hi mo123,
First off all I would like to say thank for all your hard work for the RK3288 community in general and for Nagrace HPH TV Box in particular.
Regarding your new ROM, do you think I can flash it fully in my HPH RK3288 with 4Gb of RAM and 32Gb of Storage?
Or I must keep my resource.img from my current 1.3.35 Nagrace firmware?
Thanks in advance for your support.
Keep up the good work.

[torbvea]

The R28 uses the same wifi and remote, so it might work correctly. Other user with R28 already installed ROM and it worked.
You might need to flash the boot.img and/or only resource.img from your stock ROM released after October 2014 for best compatibility.

Okey, thank you. Can I try with the boot.img and resource.img included in your ROM first? Or do I risk to brick my TV box then?

[mo123]

Yes, Nagrace is one of Rockchips best suppliers.
They were the first company to actually release a RK3288 TV Box before anyone else and their box is more stable,faster than boxes that are made recently.


My new ROM is now uploaded for everyone to try.

I'm limited by space(800MB in Windows, if I go over 1GB in Linux the ROM doesn't boot for system.img) to not install more apps automatically, will try to find a solution or wait for TWRP/CWM for RK3288 TV Boxes that will make it much easier.

There are 2 bootanimations, just rename bootanimation.zip.old to bootanimation.zip with root access to see the other one.

First boot takes a while but second boot is less than 20 seconds.

Includes latest SPMC v13.3.4 beta 1 from today(not released on Play Store, only on Freaktab) that has perfect video playback and can F/F, R/W & seek with no crashes. Also plays lots of avc/mkv files that have black screens with Kodi beta 2/3.

[The-Lord]

No, the 2GB one runs great.
I'm getting another one for free since I help out with the firmware and troubleshooting

Kudos to Nagrace for this. They are really investing in the development community.

[m1pnk]

No, the 2GB one runs great.
I'm getting another one for free since I help out with the firmware and troubleshooting