PicUntu-4.5-nand-BasicGUI installer - One file, few click install.

[sho25]

Re: PicUntu-4.5-nand-BasicGUI installer - One file, few click install.

Is this also possible on a rk3066 device, like the iMito MX1? Or is this only for rk3188?

Send from my GT-I9300 with Tapatalk

[stranzenbach]

found out myself

Hi

I used the PicUntu-4.5-nand-BasicGui installer on a stick MK809III.

The stick boots but into initramfs shell and stops.

Using dmesg i found the root file system (system.img) can not be mounted.
Using linux i tried to mount the system.img with:
mount -o loop system.img /mnt
failed. Error message: EXT4-fs bad geometry

Any help?

Found out myself: Due to missing space on disk the system.img was not unpacked completely
Picuntu works great, Thanks a lot.

[vmkogeretla]

Hi

I used the PicUntu-4.5-nand-BasicGui installer on a stick MK809III.

The stick boots but into initramfs shell and stops.

Using dmesg i found the root file system (system.img) can not be mounted.
Using linux i tried to mount the system.img with:
mount -o loop system.img /mnt
failed. Error message: EXT4-fs bad geometry

Any help?

sudo mount -t ext4 -o ro /system.img /mnt or redownload

[stranzenbach]

No Root filesystem

Hi

I used the PicUntu-4.5-nand-BasicGui installer on a stick MK809III.

The stick boots but into initramfs shell and stops.

Using dmesg i found the root file system (system.img) can not be mounted.
Using linux i tried to mount the system.img with:
mount -o loop system.img /mnt
failed. Error message: EXT4-fs bad geometry

Any help?

[vmkogeretla]

my device is mk908 (not v3)
I flashed your xubuntu-13.04-core-vmk
Selected rk3188_mk908_linux_720_defconfig-kernel.img
checked "system" section in RK Tool which was NOT ckecKed (the other four were all checked)
Erased nand (went o.k)
Flashed (went o.k) - took a while of course as it was 1.3 Gb data to write
Waited for 10-15 minutes - blue light was on but no screen output
Then unplugged the device and rebooted (waited for another 10 minutes)
No screen output and the blue lamp was off

What did I do wrong? I am willing to retry couple of more times. It would however so much more convenient to test with recovery linux kernel image if you would compile one plz.

Now I reflashed to android. Then I loop mounted your system img which I could easily convert to RFS and transfer to sd card to test recovery kernels if you are willing to produce them (I always prefere 720p because of my poor vision.

Many thanks again!

OK завтра

[sevo1984]

didn't work

link only NAND http://yadi.sk/d/R9By8N49C3kLE/
if for NAND will work, then I will compile for recovery

my device is mk908 (not v3)
I flashed your xubuntu-13.04-core-vmk
Selected rk3188_mk908_linux_720_defconfig-kernel.img
checked "system" section in RK Tool which was NOT ckecKed (the other four were all checked)
Erased nand (went o.k)
Flashed (went o.k) - took a while of course as it was 1.3 Gb data to write
Waited for 10-15 minutes - blue light was on but no screen output
Then unplugged the device and rebooted (waited for another 10 minutes)
No screen output and the blue lamp was off

What did I do wrong? I am willing to retry couple of more times. It would however so much more convenient to test with recovery linux kernel image if you would compile one plz.

Now I reflashed to android. Then I loop mounted your system img which I could easily convert to RFS and transfer to sd card to test recovery kernels if you are willing to produce them (I always prefere 720p because of my poor vision.

Many thanks again!

[Jo2010]

Can flash only android stock rom

http://yadi.sk/d/dWRSwlQwCCouX - adobeflash-chromium-arm-vmk.tar.gz

Sorry to replay late,that is bz I am not able to flash linux,I don't know why.i tried with finless flash tool and other flash tool but at end of flashing it shows run failed. I was able to flash before .now I can flash only android with rk batch tool .i think I tried to flash linux hundred times!but all failed.please help me.

[Jo2010]

Only able to flash android stock rom.

thanks for reply. now work but wifi dont want. i try with command line and not work

Sorry to replay late,that is bz I am not able to flash linux,I don't know why.i tried with finless flash tool and other flash tool but at end of flashing it shows run failed. I was able to flash before .now I can flash only android with rk batch tool .i think I tried to flash linux hundred times!but all failed.please help me.

[sevo1984]

mk908v1 nand kernel

link only NAND http://yadi.sk/d/R9By8N49C3kLE/
if for NAND will work, then I will compile for recovery

Will do so and let you know how it went on!

[oceanarecibo]

En: unfortunately we must to wait for a good porting of picuntu on mk908



Ro: din pacate va trebui sa mai asteptam pentru o portare buna a unei distributi bune pe mk908

yes indeed

[oceanarecibo]

On MK908 it will not work

EDIT: The Device is Dead now...

Have you tryed this ?

https://doc-0o-40-docs.googleusercontent.com/docs/securesc/ha0ro937gcuc7l7deffksulhg5h7mbp1/3m28pac8r5t6g8iskgasrve1on7fqr3a/1383804000000/05497358686828403223/*/0B3BfmQaKdN2LMUszMTBnLUNyY0E?h=16653014193614665626&e=download

it work.Read carefully the readme inside

If the device is "dead" try to burn an android rom (try finless rom ) to restore original partition layout.

Also pay atention to the RK loader version. Some sticks have issues with 1.20. You need to "burn"
1.24 loader
If this is not working, the "dead" maybe means a hardware problem. Or not an mk908 from tronsmart. At least the device should be recognised by the rom tool......if not, there is a problem (hw) with the device

[vmkogeretla]

I really do apologize, I've been away from the country on a business trip, didn't have chance to check the Freaktab forums! It took me a while today to try to catch up with updates. Will try to find your post now, but would appreciate if you could send me the link. Thanks!

link only NAND http://yadi.sk/d/R9By8N49C3kLE/
if for NAND will work, then I will compile for recovery

[ionutz]

waiting is to long

En: unfortunately we must to wait for a good porting of picuntu on mk908



Ro: din pacate va trebui sa mai asteptam pentru o portare buna a unei distributi bune pe mk908

[sevo1984]

en
Yes, I have compiled a kernel for recovery. Once you have not responded to my core work for NAND, on mk908v1, I can not check. I mk809iii-v1-ap6210-101j1102

rus
да я уже скомпилировал ядро для recovery. только вы не ответили, работают ли мои ядра, для NAND, на mk908v1, я проверить не могу. У меня mk809iii-v1-ap6210-101j1102

I really do apologize, I've been away from the country on a business trip, didn't have chance to check the Freaktab forums! It took me a while today to try to catch up with updates. Will try to find your post now, but would appreciate if you could send me the link. Thanks!

Rus
Мне очень жаль, я был за границей в командировке, у меня не было шанса проверить Freaktab forums! Мне потребовалось некоторое время сегодня, чтобы догнать со всеми обновлениями. Я постараюсь найти его сейчас, но был бы признателен, если бы Вы прислать мне the link. Cпасибо!

[vmkogeretla]

Thanks for your great work!!!
Are these nand only kernels? Judging by their size it does appear to be so.
Have you tried compiling any recovery linux kernels for mk908v1?

en
Yes, I have compiled a kernel for recovery. Once you have not responded to my core work for NAND, on mk908v1, I can not check. I mk809iii-v1-ap6210-101j1102

rus
да я уже скомпилировал ядро для recovery. только вы не ответили, работают ли мои ядра, для NAND, на mk908v1, я проверить не могу. У меня mk809iii-v1-ap6210-101j1102