Announcement

Collapse
No announcement yet.

TANIX TX6S Allwinner H616 Android 10.0 TV Box 2GB/16GB 2.4G+5.8G WiFi LAN Bluetooth

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts


    Check the all information about the updateFW from AllWinner and the 3rd party,
    BUT No One succeed on TX6S,
    1,Pressed RESET BUTTON can not into flash mode.SO AllWinner PhoenixSuit cant find device
    2,No Key file,SO AllWinner LiveSuit cant run update
    3,AllWinner PhoenixUSB can not read & burn H616 FW file. SO TFcard update FW fail.
    4,AllWinner DragonFace Tools cant open H616 FW file also.


    UNTIL checking the IC development manual to found out how to setup into flashmode.

    YES,buy a cable very easy,UPDATE FW very easy .The process of finding solutions is complex.

    TX6S software system is very immature and full of bugs

    Comment


      Originally posted by onlyonce View Post
      Check the all information about the updateFW from AllWinner and the 3rd party,
      BUT No One succeed on TX6S,
      1,Pressed RESET BUTTON can not into flash mode.SO AllWinner PhoenixSuit cant find device
      2,No Key file,SO AllWinner LiveSuit cant run update
      3,AllWinner PhoenixUSB can not read & burn H616 FW file. SO TFcard update FW fail.
      4,AllWinner DragonFace Tools cant open H616 FW file also.

      UNTIL checking the IC development manual to found out how to setup into flashmode.
      YES,buy a cable very easy,UPDATE FW very easy .The process of finding solutions is complex.
      TX6S software system is very immature and full of bugs
      Your comment is confusing, hard to understand your point of interest. Are you just saying how bad firmwares are? Or, Are you still having problems installing firmware, or connecting device to computer?

      You know the Reset Button is hidden next to SDcard slot on side of device! (Reset button is not at rear of device, this will cause problems if you didn't know this). Best thing to do is dissemble TVbox and cut out the plastic fin that blocks the reset button so you can easily access the button when you put the case back together.

      I always use Phoenix_USB_Tool on windows computer to Flash the different Allwinner Firmwares,
      1) load firmware in Tool
      2) click START
      3) hold Reset button down
      4) connect USB cable while you keep holding Reset down
      5) Windows system makes confirmation sound that device is connected when connected, but the Tool doesn't start Burning firmware immediately, it takes some time, maybe 1 minutes for Tool to start showing progress.
      6) plug and connect TVbox to TV and wait 5 minutes for new firmware to finish first-boot start-up processes.


      Comment


        Found a work-a-round for the Network issues of the TX6S, to get the best possible speed for Networking in this device you must use a USB-to-Ethernet adapter in the USB 3.0 connection. The adapter I used was TPlink USB3.0-to-Gigabit_Etherenet connector and the device can now connect at a maximum of 90-100 Mbps download speed.

        Comment


          Originally posted by gefattern View Post
          Hi ,

          Nice to see , Risky Dude , hope both calm down , had 2 Flags because of it ,

          Flagger did the right , good hope for the Future that they do it right now , we

          all have Errors , nobody is pefect , but to know and change it is the best thing ,

          i know it is frustrating to see , that there is no Support for the Box that bought ,

          next Time they buy a Shield , or Ugoos or similar better supported China Boxes ,

          greetings / gefattern
          Check out youtube, see the comments about Nivida Shield from people who bought one before shelling out around $200 for one.

          Not worth it, especially if you're not a PC gamer/Nivida fanboi.

          Comment


            Originally posted by RiCkLaR_atvX View Post

            Your comment is confusing, hard to understand your point of interest. Are you just saying how bad firmwares are? Or, Are you still having problems installing firmware, or connecting device to computer?

            You know the Reset Button is hidden next to SDcard slot on side of device! (Reset button is not at rear of device, this will cause problems if you didn't know this). Best thing to do is dissemble TVbox and cut out the plastic fin that blocks the reset button so you can easily access the button when you put the case back together.

            I always use Phoenix_USB_Tool on windows computer to Flash the different Allwinner Firmwares,
            1) load firmware in Tool
            2) click START
            3) hold Reset button down
            4) connect USB cable while you keep holding Reset down
            5) Windows system makes confirmation sound that device is connected when connected, but the Tool doesn't start Burning firmware immediately, it takes some time, maybe 1 minutes for Tool to start showing progress.
            6) plug and connect TVbox to TV and wait 5 minutes for new firmware to finish first-boot start-up processes.

            Actually, the best thing to do is take an old credit or similar card and cut a strip of plastic off it using scissors so that it will slide inside/into the vent slot in front of the reset button so you can press the button as you would using a paper clip or toothpick.

            No need to damage or dissemble anything.



            Comment


              Originally posted by RiCkLaR_atvX View Post

              Your comment is confusing, hard to understand your point of interest. Are you just saying how bad firmwares are? Or, Are you still having problems installing firmware, or connecting device to computer?

              You know the Reset Button is hidden next to SDcard slot on side of device! (Reset button is not at rear of device, this will cause problems if you didn't know this). Best thing to do is dissemble TVbox and cut out the plastic fin that blocks the reset button so you can easily access the button when you put the case back together.

              I always use Phoenix_USB_Tool on windows computer to Flash the different Allwinner Firmwares,
              1) load firmware in Tool
              2) click START
              3) hold Reset button down
              4) connect USB cable while you keep holding Reset down
              5) Windows system makes confirmation sound that device is connected when connected, but the Tool doesn't start Burning firmware immediately, it takes some time, maybe 1 minutes for Tool to start showing progress.
              6) plug and connect TVbox to TV and wait 5 minutes for new firmware to finish first-boot start-up processes.

              Actually, the best thing to do is take an old credit or similar card and cut a strip of plastic off it using scissors so that it will slide inside/into the vent slot in front of the reset button so you can press the button as you would using a paper clip or toothpick.

              No need to damage or dissemble anything.

              This is what I came up with to acess the reset button on my MXQ Pro 4K and TX6 Type devices:
              Click image for larger version

Name:	IMG_20200320_123400.jpg
Views:	536
Size:	65.2 KB
ID:	800143

              Comment


                Has anyone had an issue with this box where it won't power up if the reset button is being held down?

                Comment


                  hello this box is good or not? or bad firmware?

                  does anywant mod for atv?

                  Comment


                    TX6S OTA update 23.03
                    MEGA provides free cloud storage with convenient and powerful always-on privacy. Claim your free 50GB now!

                    Comment


                      Originally posted by kokovi4 View Post
                      TX6S OTA update 23.03
                      Latest?? How about temp??

                      Comment


                        Yes, from yesterday, So, little good , continue test .

                        Comment


                          it is the same shit (sorry), but in a higher version.
                          nothing works, and it's impossible to install apps.

                          Waiting for a new version.

                          Comment


                            Originally posted by kokovi4 View Post
                            TX6S OTA update 23.03
                            Any Changelog on this new update?

                            Or did you notice any significant changes with this new update?

                            Comment


                              Nothing.

                              Comment


                                Somebody try Local Update - dynamic system update.Some people can update to 20200331 FW
                                I have 20200323 and system can't update

                                Comment

                                Working...
                                X