If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Announcement
Collapse
No announcement yet.
Announcement
Collapse
No announcement yet.
Pipo users: READ THIS BEFORE FLASHING A KITKAT ROM!!!!!
I try not to provide duplicate information in multiple threads. Sorry for the confusion, but it's just best for everyone to know where to go to get the appropriate information.
Actually, you simply stated the whole process in your post. It isn't that difficult, but it IS something you MUST do.
Dear Riley,
I hope you can help me. I forgot to mark the loader when coming back from KK, and now my tablet wont start. Always black screen.
When I connect the usb and press the power for 10 seconds, it appears as unknow device and doesnt allow me to change the drive.
If i release the power button, it turns off. I cant manage to open it, I dont have the tools. Is there any other way to fix it?
Randy Freaktab Developer, Product Reviewer, Moderator and "Flashaholic". Read my BIO Here
Be sure to donate to support Freaktab.com. If any of my development work makes a positive difference for you, please make a donation to support future RileyROM's. Donate here
Surely there must be a video already on YouTube that shows how to open a tablet. I would do it....but I'm still a work.
Randy Freaktab Developer, Product Reviewer, Moderator and "Flashaholic". Read my BIO Here
Be sure to donate to support Freaktab.com. If any of my development work makes a positive difference for you, please make a donation to support future RileyROM's. Donate here
I found a link for stock kitkat (DS977_4.4_20140220)Rom and want to try it. If i want to downgrade afterwards to rr 1.9 (jb) how do i do that?
Do i use your flash tool that comes with rr 1.8 (kk) to erase nand before flashing rr 1.9?
Randy Freaktab Developer, Product Reviewer, Moderator and "Flashaholic". Read my BIO Here
Be sure to donate to support Freaktab.com. If any of my development work makes a positive difference for you, please make a donation to support future RileyROM's. Donate here
Pipo M8 max pro owner. Bricked it after flashing kitkat 4.4 without new loader
Almost same as eljuggy-> ("Testing device 100%" or Total(16384) Current(16384) when flashing (no mask rom then)
I can't seem to get mask mode even shorting pin 7&8 or 8&9, i could not find the datasheet for my nand, but it is the exact same as the picture by Riley. i have manage to reset via shorting the pins, but it always shows "Found RKAndroid loader Rock USB". Any tips? Thx!
Experiment with different pins...it shouldn't hurt. You may have to continue holding the power button.
Sent from my M6Pro using Tapatalk
Randy Freaktab Developer, Product Reviewer, Moderator and "Flashaholic". Read my BIO Here
Be sure to donate to support Freaktab.com. If any of my development work makes a positive difference for you, please make a donation to support future RileyROM's. Donate here
Also during flash the test phase was testing 8192 blocks and not 16384...
The 3 last steps I did were :
1) Tried once more to flash 4.4 using RKDevelopTool
- erase all blocks + erase ID
- flashed loader 2.10
- flashed 4.4 sergiopoveroni - failed but I saw again the test of 16384 blocks : progress !
- Erase ID again
2) Flashed 1.24 bootloader only (only box checked) using ROM_Flash_Tool_137
3) Flashed Pipo Stock M8 pro 4.2.2 chinese with RKBatchTool 1.7 and to my great surprise : success !
Well now I think I'll try again flashing 4.4 but with correct 2.10 bootloader I'm feeling lucky !
Experiment with different pins...it shouldn't hurt. You may have to continue holding the power button.
Sent from my M6Pro using Tapatalk
Thank you for the reply. I have cycle through all pins on top, with and without pressing the power button. No mask mode, only reset at pin 12-13 (kinda like pressing the physical reset button)
No, they will be sequential. Sometimes it's hard to make good contact.
Sent from my M6Pro using Tapatalk
Randy Freaktab Developer, Product Reviewer, Moderator and "Flashaholic". Read my BIO Here
Be sure to donate to support Freaktab.com. If any of my development work makes a positive difference for you, please make a donation to support future RileyROM's. Donate here
Figured out how to go into maskrom mode. I had to pull out the power Cable and then replug while shorting Nand pin 8-9 . got into mask mode, erased ibd, flashed rileys rom 2.1.2. Tablet booted fine after. Thanks riley, you are awesome!
Thanks for the clear instructions. Sometimes I have to ask a question to clarify, but by and large the instructions you guys are including make it easy.
If you read my bio...I'm a journalist by education...Fire Captain/Paramedic by trade (28 years). I'm always writing procedures for lifesaving techniques...so writing these directions comes naturally...although not on the same level of importance.
Thanks for the feedback...I truly appreciate it.
Randy Freaktab Developer, Product Reviewer, Moderator and "Flashaholic". Read my BIO Here
Be sure to donate to support Freaktab.com. If any of my development work makes a positive difference for you, please make a donation to support future RileyROM's. Donate here
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
Comment