NEW - 900 Supersport 1.1 Jelly Bean rooted ROM for Cube U30GT Mini

[79kiko]

I have this rom. Please look video. This makes When is on the Charger.

[900supersport]

Re: NEW - 900 Supersport 1.1 Jelly Bean rooted ROM for Cube U30GT Mini

I've never seen that before, does it only happen when on power?

[vinsouille]

I have this rom. Please look video. This makes When is on the Charger.

I have the same problem when I use another charger than that of origin. They have all a power lower than that of origin
I think that chargers have to make at least 2000mAh so that the tablet works when the charger is connected.

[79kiko]

900superspor: This make only if I put charger. I use only the origin charger.

[900supersport]

Re: NEW - 900 Supersport 1.1 Jelly Bean rooted ROM for Cube U30GT Mini

I'd be looking to replace the charger.

[79kiko]

Can you play a game Asphalt 7 on this ROM? The game stops when loading and then restart and goes in loop with the restarting.

[Rahta]

The xbox gamepad does´t work. Any idea?

[a29psx]

I always get this type of error



I also get similar error with the default flashing program from the original firmware
which read fail in testing or checking my device something

any suggest ?
thanks for your help

[a29psx]

I always get this type of error

[ATTACH=CONFIG]1101[/ATTACH]

I also get similar error with the default flashing program from the original firmware
which read fail in testing or checking my device something

any suggest ?
thanks for your help

thanks to lasvegaswings I used another cable from the motorola xoom and it seem to be ok now
the original cable from cube is just rubbish

anyway, thanks 900supersport for this work

[Sarunaszx]

charger

hello, my Cube tablet is arriving and i'm sure i will have to buy a new charger, because it is going to be US type, not EU. What kind of charger could you recommend?

[a29psx]

hello, my Cube tablet is arriving and i'm sure i will have to buy a new charger, because it is going to be US type, not EU. What kind of charger could you recommend?

just get a wall plug US > EU adapter. I'm sure you can get one from your local electronics store for about $5 or less

[Sarunaszx]

just get a wall plug US > EU adapter. I'm sure you can get one from your local electronics store for about $5 or less

Yeah, that would be a solution.. but then the charger will get really big, uncomfortable for carrying it. Besides, I have heard that original charger is bad...

[a29psx]

Yeah, that would be a solution.. but then the charger will get really big, uncomfortable for carrying it. Besides, I have heard that original charger is bad...

it's up to you man, I find this an easy and acceptable solution

My original charger is acceptable, not getting hot during charging
and I think the DC-in plug is not a popular style so it is not easy to find
if you're realy want to get another charger, make sure to get a 2.5amp at least

[greatestpyro]

I'm in trouble

I followed your instructions to the letter. I have three of these tablets that I need to root. Initially I had some issues with the drivers and booting into the flash mode but sorted that out. Got the first tablet in flash mode, erased the NAND, all is good, then on write flash it wrote the entire 535539K then when it went to check the data it failed at 52K. I was unable to do anything so I unplugged it and turned it on. It went to Clockwork and did everything as expected and worked perfectly. It didn't go as planned but it worked correctly and that's all that matters.

Tablet #2- After the first one acted weird I was hesitant but began the same procedure for number 2. The NAND erase went fine. The flash got screwed up while writing not even 20% into it. What can I do? It won't even turn on now. I need to fix this. The only good news is that the device is still showing up as Found in your program.

UPDATE: So after it going all half brick on me it actually allowed me to erase NAND and flash again. It wrote the whole thing again and then failed at exactly 52K on the check again. I unplugged it turned it on and it was good to go.

I had no problems with the third one but again it failed the check at exactly 52K. Unplugged it and manually booted it with no problem.

[felixarch]

I followed your instructions to the letter. I have three of these tablets that I need to root. Initially I had some issues with the drivers and booting into the flash mode but sorted that out. Got the first tablet in flash mode, erased the NAND, all is good, then on write flash it wrote the entire 535539K then when it went to check the data it failed at 52K. I was unable to do anything so I unplugged it and turned it on. It went to Clockwork and did everything as expected and worked perfectly. It didn't go as planned but it worked correctly and that's all that matters.

Tablet #2- After the first one acted weird I was hesitant but began the same procedure for number 2. The NAND erase went fine. The flash got screwed up while writing not even 20% into it. What can I do? It won't even turn on now. I need to fix this. The only good news is that the device is still showing up as Found in your program.

UPDATE: So after it going all half brick on me it actually allowed me to erase NAND and flash again. It wrote the whole thing again and then failed at exactly 52K on the check again. I unplugged it turned it on and it was good to go.

I had no problems with the third one but again it failed the check at exactly 52K. Unplugged it and manually booted it with no problem.

Hi, i had the same problem with my computer running windows XP. Before installing service pack 3 everything was fine. After, the loader was acting weird. I had 2 minicube. Sometime i was able to erase the memory and sometimes not (i had to restart the loader). After, sometime i was able to install the ROM but i could never run the "check install".

i've tried with my girlfriend computer (window7) and everything was fine...

I would suggest you to try another computer and/or another usb cable and usb port