NAND Chip Mask ROM Mode Short Location

[Hotrod1]

Hi Hotrod1, thanks for answer. Here you have them... it is a generic brand -Profiber 4/32Gb- but it is observed that the board is X96, I assume it will be similar to X96 MAX Plus Q2 4/32Gb or X96 MAX Plus 4/32GB.
Any help will be welcome, I have tried everything without success.

front (https://ibb.co/LSL0j87)
back (https://ibb.co/T131LsF)

Thanks, Bernardo.

Sorry forgot to put the video link into my last post.

https://youtu.be/OyZJVD5SbSY

[soldiaz]

x96 max plus: short nAND to SD ground: https://uploads.tapatalk-cdn.com/202...d1121a49b9.jpg

Try any pins on BGA chip backside and try to short to SD card's housing ground

[Hotrod1]

Post a good quality pic of each side of your board and the complete model name and all the hardware specs and I'll see if I can help you out.

You must touch something metallic across the 2 pins in the red circle in this pic. Then connect the usb to the box. Watch this video he shows you how to unbrick using Mask ROM. You must load the ROM in the Amlogic burner before you connect the usb.

https://imgur.com/AArFNMz

[jucca]

Hi guys.

Have X96 Max 3, had Slimbox ROM, rooted, and TWRP installed.
Wanted to go back to stock because didn't manage to get Netfilx in FHD.

First I installed official recovery, then, official ROM X96Max_Plus2_20200901-1005 ROM
That went without any errors, but after reboot, it stucked there.
Tried to short pin it, nothing. (already done this few times before, every time worked, till now)

But, if I leave it connected via USB A-A cable to my computer, after 10 mins it boots, but UBT won't recognize it.
Tried few versions of UBT, but no luck.

Pics are here:

[bertdf]

Hi Hotrod1, thanks for answer. Here you have them... it is a generic brand -Profiber 4/32Gb- but it is observed that the board is X96, I assume it will be similar to X96 MAX Plus Q2 4/32Gb or X96 MAX Plus 4/32GB.
Any help will be welcome, I have tried everything without success.

front (https://ibb.co/LSL0j87)
back (https://ibb.co/T131LsF)

Thanks, Bernardo.

Post a good quality pic of each side of your board and the complete model name and all the hardware specs and I'll see if I can help you out.

[Hotrod1]

Hi Hotrod1, I have a totally bricked Q5x3_141 V4.1 device, it does not turn on any lights and the USB is not detected... I have tried your suggestion and still not "waking up", you have been able to unbrick your device? How? Any guidance you can give me will be welcome.

Thanks, Bernardo.

Post a good quality pic of each side of your board and the complete model name and all the hardware specs and I'll see if I can help you out.

[stajkov28.04]

Here is a photo of the board, who can help.

[stajkov28.04]

[stajkov28.04]

[stajkov28.04]

[stajkov28.04]

Hi all! Help where to close the contacts on the TV box x88 pro s on the Allwinneri h616 processor to reset the memory chip, prefix brick

[bertdf]

Hi Hotrod1, I have a totally bricked Q5x3_141 V4.1 device, it does not turn on any lights and the USB is not detected... I have tried your suggestion and still not "waking up", you have been able to unbrick your device? How? Any guidance you can give me will be welcome.

Thanks, Bernardo.

The picture in comment #822 shows the wrong pins. These are the correct pins confirmed.

https://imgur.com/AArFNMz

[Hotrod1]

could be more options! Even possible to short using SD card housing's ground....

Good to know. Thank you.

[soldiaz]

The picture in comment #822 shows the wrong pins. These are the correct pins confirmed.

https://imgur.com/AArFNMz

could be more options! Even possible to short using SD card housing's ground....

[Hotrod1]

The picture in comment #822 shows the wrong pins. These are the correct pins confirmed.

https://imgur.com/AArFNMz