H96 Pro Plus short pin unbrick help

[hcardoso483]

Hi,

I had the same issue as you stuck at 2%.

I switched to an older laptop with a USB 2.0 port and it then successfully flashed.

That happened becouse the laptop can't power up the box properlyyou should do this way
1 load the IMG file in the Amlogic burning tool make sure that reboot after success is selected
2 After the IMG is loaded press start
3 Insert you USB male to male in to the USB of the PC and in the USB closest to the power port of the box,
4 As soon as your box is detected by the USB burning tool plug in the power supply that came with your box
Now you will have enough power for the flash operation to be successful
5 After success Disconect the USB cable and press stop

[hcardoso483]

Blue board, CZ-S32-V6, came faulty - when turned on the blue leds light on and nothing appears on the display. Tried to flash it with Burning_Tool using several ROMs for V5/V6. Tried also different power adapter which is proven to be good and working. Tried also on several computers. Every time is the same - once it reaches the 7% it shows the following error: [0x32030201]Uboot/Get result/DiskInitial error

Please, advise.

Not enough power to flash operation plug in your power supply as soon as burn process starts, if it stops again just recicle the USB connection

[minus-human]

Not enough power to flash operation plug in your power supply as soon as burn process starts, if it stops again just recicle the USB connection

Тhe power adapter has always been plugged. As I sad, I even tried several power adapters.

[zeroprobe]

That happened becouse the laptop can't power up the box properlyyou should do this way
1 load the IMG file in the Amlogic burning tool make sure that reboot after success is selected
2 After the IMG is loaded press start
3 Insert you USB male to male in to the USB of the PC and in the USB closest to the power port of the box,
4 As soon as your box is detected by the USB burning tool plug in the power supply that came with your box
Now you will have enough power for the flash operation to be successful
5 After success Disconect the USB cable and press stop

No, when I had the 2% problem, I was using my desktop computer. So no power issues.

It's definitely a USB port issue. Try on older computers people.

[hcardoso483]

No, when I had the 2% problem, I was using my desktop computer. So no power issues.

It's definitely a USB port issue. Try on older computers people.

usb power suply on a computer no metter if is desktop or laptop or notebook, the usb suply is under 1 amp you need at least 1,5 amps for power up nundroid flash

[hcardoso483]

Тhe power adapter has always been plugged. As I sad, I even tried several power adapters.

you cant have your power adpter on when you connet the usb becouse as soon as it receves power from adpter ti will start boot, you need to 1st connect the usb and when the usb burn tool sees the box you connect power adapter

[minus-human]

you cant have your power adpter on when you connet the usb becouse as soon as it receves power from adpter ti will start boot, you need to 1st connect the usb and when the usb burn tool sees the box you connect power adapter

I tried that many, many times. No matter what the sequence is the result is the same every time - it stops at 7%

[hcardoso483]

I tried that many, many times. No matter what the sequence is the result is the same every time - it stops at 7%

What is the log message?
Some boxes are a little tricky to flash this way i know it works coz mi H96 pro is the same and this is the way it works

1 Load the rom you are about to flash on the usb burning tool
after rom loaded Press start
2 coneect the usb plug only same time press reset button as soon as your box gets detected by the tool release the button
this will get tou to 2% or so but before you get to 2 % connect the power plug now it wont stop at 2% but i can stop at 7% just after formating
3 if it stops at 7% simply recicle the usb connection it will pick from there

[tariche]

Blue board, CZ-S32-V6, came faulty - when turned on the blue leds light on and nothing appears on the display. Tried to flash it with Burning_Tool using several ROMs for V5/V6. Tried also different power adapter which is proven to be good and working. Tried also on several computers. Every time is the same - once it reaches the 7% it shows the following error: [0x32030201]Uboot/Get result/DiskInitial error

Please, advise.

Hi,
I have exactly the same board. Tried to flash several ROMs including "original" provided by banggood during refund process. Every time process gets stuck at 7% with the same error message as in the quote. Anyone, figured this out?

[hcardoso483]

Hi,
I have exactly the same board. Tried to flash several ROMs including "original" provided by banggood during refund process. Every time process gets stuck at 7% with the same error message as in the quote. Anyone, figured this out?

when you get to 7% and the flashing fails just recycle the connection it will go thru, disconnect and reconnect the usb cable do not touch any thing else, it will restart to flash but this time it will complete the procedure, good luck

[tariche]

I 've tried it 40 times and it still stops at 7%. Anyhow, thank you for the suggestion.

[gefattern]

Hi,
I have exactly the same board. Tried to flash several ROMs including "original" provided by banggood during refund process. Every time process gets stuck at 7% with the same error message as in the quote. Anyone, figured this out?

Hi ,

i am not a Pro in AML , but this Error Message , sounds like the Flashtool has Problems

to get in contact with the Disk/Nand or ever called , maybe something is damaged ,

further good luck / gefattern

[tariche]

maybe something is damaged ,

further good luck / gefattern

You are probably right.

Anyhow, not to sad since banggood is sending replacement.

Thank you all for your help.

[gefattern]

You are probably right.

Anyhow, not to sad since banggood is sending replacement.

Thank you all for your help.

Hi ,

that sounds logic , good luck with new Box ,

greetings / gefattern

[thewebexpert]

My S912 box (T9X PRO) was bricked, the reset button was not working, shorted the two pins with a butter knife (see post 12 with the picture) and presto, the box appeared in the usb burning tool. fantastic! Thank you so much!