Tanix TX9 Pro TV Box Amlogic S912 Android 7.1 Dual WiFi, Gig Lan BT 4.1

[georgesat20]

that procedure only makes sense when the box is bricked
maybe try another rom, this one works on Tanix TX9 Pro

https://uptobox.com/zf1qe8tmrvg9

Again the same error Alianato

[Alianato]

Again the same error Alianato

not very good news, perhaps it's broken for good, I am out of suggestions

[Kabelventje]

Does anyone can help me ?

Maybe you fried one or more of your voltage regulators in the yellow circles. Power up the unit and measure on all regulators on the pin with red arrow.There should be 1V and or 3V.(look at printed text on board).

[georgesat20]

Thanks so much for your reply Kabelventje I will check and I will inform

[trebor]

Can you take a close picture of PCB...may be we can see what has BLOWN UP, 12v in to 5v is not good as you have found.

[georgesat20]

thanks for your help again

[trebor]

Hello georgesat20
I can see nothing Obvious to what may have gone...and as with electronics....the weakest link normally goes first
Maybe friend you have who is tech can track and trace.
Others may add to this but you need to know what you are doing to resolve. no a quick fix I am sorry to say
Learn from this mistake.
Never unplug power pack especially when 12 and 5v can be mixed.
I have killed one or two,
But have spare power pack remote and case and maybe some parts

[kron574]

I have four tx9 boxes that i updated with the flash drive method two went smooth the second two after update they boot get to the Android logo then go to a black screen sitting there?

[Kabelventje]

I have four tx9 boxes that i updated with the flash drive method two went smooth the second two after update they boot get to the Android logo then go to a black screen sitting there?

Try to use the Amlogic Flash tool with the proper image.
Both can be downloaded from the Tanix site.

[gino.asso]

Hi all,
i have accidentally, turned off wifi connection, and it wasn't possible to turn it again. I've updated my TX9 pro to the latest firmware (20180205) but nothing changed. Could you help me?

[Kabelventje]

You can switch on wifi in the settings button in the app menu screen , also in " more settings" . When cable is plugged in, the wifi is disabled.
Do you get a error while turning wifi on ?
If so , a factory reset would help.

Grtz André.

[kron574]

Kabelventje No go I have two that bricked i think. I can't access recovery on either both have no Boot logo on the front and both don't display nothing . The first one when i try and flash with burning tool it fails around 2% with a 0x10105002 error. Second one with same Usb same and same firmware Feb2018 it flashes fine but says boot with no image now, but when i plug in a hdmi cord it doesn't show boot at all? This all started when they arrived they were freezing a lot tried doing a factory reset that didn't help then i went and flashed the new Feb firmware and now im bricked

[kron574]

Alianato which firmware link is dead i got the same error on one of my boxes like georgesat20 I know it's not my usb or the way im flashing becaues i have flashed several other boxes fine prior.

[Alianato]

Alianato which firmware link is dead i got the same error on one of my boxes like georgesat20 I know it's not my usb or the way im flashing becaues i have flashed several other boxes fine prior.

I am not sure I understand your post, I suggest reading the two topics I created regarding Tanix TX9 Pro/Vorke Z6 Plus roms

http://freaktab.com/forum/tv-player-...ms-android-7-1

http://freaktab.com/forum/tv-player-...7-std-ultimate

[drakman]

I have not managed to play smooth 24p content with this box and kodi 17.6. Even if I set the resolution in the tanix at 1080p 24hz when I play a movie at 24fps the playback is choppy. This is happening only on Kodi and not in narive android player. Any suggestions? I have already try all possible settings via Kodi such as adjust refresh rate to screen etc with no success.

[wrxtasy]

I have not managed to play smooth 24p content with this box and kodi 17.6. Even if I set the resolution in the tanix at 1080p 24hz when I play a movie at 24fps the playback is choppy. This is happening only on Kodi and not in native android player. Any suggestions? I have already try all possible settings via Kodi such as adjust refresh rate to screen etc with no success.

Read what I posted at the bottom of the following Kodi post:
https://forum.kodi.tv/showthread.php...420#pid2782420

Basically you need to set Android system resolution of 50Hz and reboot and also use SPMC 16.7.04 with the Sync Playback to Display option enabled. (Settings > Videos > Playback)
Your TV must have a 50Hz mode in Android settings > Display > Screen Resolution.

You will lose all audio passthrough, but video playback will be nice and smooth on TV's that also have a little bit of motion smoothing enabled.