Kit Kat 4.4.2 RK3066 (Fully Working)

[sam tyler]

http://www.freaktab.com/showthread.p...-UG007II-Stick I use this one now.and I no longer get power issues or frozen screen problems. and I still use my normal charger.

[davidw]

This ROM carries with it a minor HDMI audio bug persistent in KitKat update.

HDMI doesn't send audio to the TV when device is resumed from standby.

To solve the issue, always resume device from standby before powering on TV. Turn device on, then turn TV on.

The audio issue is caused by Rockchip's KitKat audio kernel configuration. The device expects a specific response from the HDMI sink, if it isn't found it effectively mutes the HDMI audio by treating the device as a DVI interface. 'rk30-hdmi: warning: EDID error, assume sink as DVI'

I just have to ask since this seems so related to my troubles on the Neo X5 (on both this and Finless 1.3). I find when I turn on my HDTV, it can often crash the machine. Lots of research shows the machine enters some kind of loop putting output on the kernel log but is effectively dead and has to be powered off. I have seen this sometimes in the kernel log:

[  431.776475] lcdc1: dclk:74250000>>fps:60 rk30_load_screen for lcdc1 ok!
[  431.783143] rk30 lcdc1 clk enable...
[  431.786737] lcdc1: dclk:74250000>>fps:60 rk30_load_screen for lcdc1 ok!
[  431.793394] lcdc1 wakeup from standby!
[  431.797168] lcdc1 win1 open,atv layer:2
[  432.111393] rk30-hdmi rk30-hdmi: Removed.
[  432.115435] no layer of lcdc1 is used,go to standby!
[  432.120420] rk30 lcdc1 clk disable...
[  432.124096] lcdc1 win1 closed,atv layer:0
[  432.142390] [EDID] check header error
[  432.146512] rk30-hdmi rk30-hdmi: [HDMI] parse edid base block error
[  432.152820] rk30-hdmi rk30-hdmi: warning: EDID error, assume sink as HDMI !!!!
[  432.159891] rk30-hdmi rk30-hdmi: warning: no CEA video mode parsed from EDID !!!!
******** Show Sink Info ********
[  432.171232] Support video mode: 
[  432.174503]  1920x1080p@60Hz.
[  432.177503]  1920x1080p@50Hz.
[  432.180497]  1920x1080p@30Hz.
[  432.183483]  1920x1080p@25Hz.
[  432.186464]  1920x1080p@24Hz.
[  432.189441]  1280x720p@60Hz.
[  432.192345]  1280x720p@50Hz.
[  432.195452]  720x576p@50Hz.
[  432.198272]  720x480p@60Hz.
[  432.201077] ******** Show Sink Info ********
[  432.205408] lcdc1: dclk:74250000>>fps:60 rk30_load_screen for lcdc1 ok!
[  432.212099] rk30 lcdc1 clk enable...
[  432.215809] lcdc1: dclk:74250000>>fps:60 rk30_load_screen for lcdc1 ok!
[  432.222502] lcdc1 wakeup from standby!
[  432.226285] lcdc1 win1 open,atv layer:2

Similar to but not quite what you mention. And not shown at the time of the crash (see below for that).

I have my Neo X5 connected to other HDTV and this seems to happen only on mine and only after the Neo has been sitting for a long time (many hours) with the TV off. I have tried using the Android Developer option to prevent the device going into standby. But I am not sure this is enough since I do see references to return to and wakeup from standby for the lcdc1 in the log info.

Here is what is shown at the time of the crash:

[35102.147945] ******** Show Sink Info ********
[35102.148041] Support video mode: 
[35102.148099]  1920x1080p@60Hz.
[35102.148168]  1280x720p@60Hz.
[35102.148215]  720x480p@60Hz.
[35102.148259] Support audio type: LPCM
[35102.148319] Support audio sample rate: 
[35102.148373]  32000
[35102.148420]  44100
[35102.148453]  48000
[35102.148486]  96000
[35102.148526]  192000
[35102.148561] Support audio word lenght: 
[35102.148614]  16bit
[35102.148654]  20bit
[35102.148693]  24bit
[35102.148728] Support audio type: AC3
[35102.148785] Support audio sample rate: 
[35102.148839]  32000
[35102.148871]  44100
[35102.148911]  48000
[35102.148945] Support audio word lenght: 
[35102.149004]  16bit
[35102.149045]  20bit
[35102.149078]  24bit
[35102.149111] ******** Show Sink Info ********
[35102.149213] lcdc0: dclk:148500000>>fps:60 rk30_load_screen for lcdc0 ok!
[35102.149342] rk30 lcdc0 clk enable...
[35102.149423] lcdc0: dclk:148500000>>fps:60 rk30_load_screen for lcdc0 ok!
[35102.149531] lcdc0 wakeup from standby!
[35102.149594] lcdc0 win1 open,atv layer:2
[35102.149679] lcdc0 win0 closed,atv layer:2
[35102.149757] lcdc0 win2 closed,atv layer:2

And then it loops printing dump information on the log.

This is a real pain and I am not sure how to deal with it. If you can provide any more details on this bug maybe I can find out more about my problem. Or maybe I can find a way to prevent the device going into standby.

Thanks for any tips.

[sam tyler]

i may have come across an answer to ramdom reboots,black outs and Lock ups with this rom.this is not a cure, all but it worked on my mk809ii(with this rom installed)what i did was to install no-frills cpu control from playstore,(hopefully you have rooted this rom)and i checked the max.clock freq,and it was set to 1.512ghz. i took it down to 1.272ghz,(i didn`t touch the min.clock freq) and i also set the governer to performance.(it was set to interactive)i pressed apply and rebooted the device.the only problem i find as the rom does not have a power off setting,just a standby or reboot setting.so if you leave the device on standby,the no-frills cpu controls you set will stay,but if you turn off the device,you may have to re apply the settings.im also using a reboot apk from a finlessbob rom(4.2.) to turn the device off, and as i said,if you do that you will have to re apply the settings in no-frills cpu.but so far so good,the device has been on for over six hours using xbmc,watching films and using a usb memory stick via a usb powered hub,and ive had no reboots,blackouts etc.as i said,this may not work other devices,its working on mine.hope this helps other people out,as i do like this rom,(except for the reboots! ) and yes my device does get hot but not as it did before,again,i hope this helps,and dont blame me if your device goes pop!

[dirtytuga]

Hi.
Please confirm (or not) if this rom is also for MK808 (without B).
Thank you

[doz]

Could anyone reupled the cwm-flashable OC kernel? The link in the first post is deleted.
Thanks

[fr4nc3sc0]

Hello, can anyone give me the zip file (4.4.2) to be loaded via CWM? Or cyanogenmod?
I've a mk802III (8g) with rk3066

[KRWiFi]

Hello.

I have Imito MX1 and i would like to map/mount network drive (WD My Cloud) to expand memory. Is there any way to do this. Cifs manager doesn't work.

regards

[tonyk3]

Hello

I've installed this & looking great! But I'm also trying to get my 20" touchscreen overlay working:

touchscreen model 03fc:05d8
and I've got this ko from the manufacturer: https://drive.google.com/file/d/0B3Q...ew?usp=sharing

I've tried using an idc to load the ko - it changed the touch but still wasn't working (all I get is a single touch registered wherever the mouse already is, not where I touch).

Sorry, I don't know enough about this, what should I do??

Thanks

Tony

[Akure]

MK808B with MTK chipset

Rom works well pairs with Bluetooth mouse and keyboard but does not work, RKRemoteControl FAILS TO DETECT STICK eHomeMediaCenter is working, I did not flash OC CWM file unavailabe for download. What do i need to do to fix these issues MY STICK MK808B with MTK chipset

[joaoluizt]

Could anyone reupled the cwm-flashable OC kernel? The link in the first post is deleted.
Thanks

I need it too

[joaoluizt]

Sounds like a power supply issue. Have you tried again with the laptop that originally allowed the device to work properly? If you go back to the laptop and everything works then it's surely a power issue.

I have a 3.5A power supply running mine.

Hi Shomari, can you post the OC Kernel from the first post please. The link is Off! Thanks!!

[Akure]

RKM Remote issue was smartphone issue

Rom works well pairs with Bluetooth mouse and keyboard but does not work, RKRemoteControl FAILS TO DETECT STICK eHomeMediaCenter is working, I did not flash OC CWM file unavailabe for download. What do i need to do to fix these issues MY STICK MK808B with MTK chipset

RKM Remote issue was smartphone issue, still having issue with no Bluetooth paring with devices but not working? is there a fix?

[joaoluizt]

Ok Shomari.
In the first place i install this one

Overclocked Kernel - 1080p (try at your own risk - CPU 1608/GPU 400/DDR 600):https://mega.co.nz/#!6N5RVIBD!48i4hG...g85DAQ7LYSUahE

and what you are saying is that i install this one to try

OC Kernel - CWM flashable:http://ge.tt/8IXOyRn1/v/0?c

Correct?

Well, after this i did what you said i install the kernel by CWM.
The device boot but a few seconds in the android luncher it frezes.
I think my device can´t handle the CPU 1608/GPU 400/DDR 600
The most i think it can handle is CPU 1500/ GPU 400/ DDR 533
Can you help me doing a KERNEL with this CPU 1500/ GPU 400/ DDR 533 ????
Thanks for it.

you downloaded the "Overclocked Kernel - 1080p (try at your own risk - CPU 1608/GPU 400/DDR 600)"? Could you send to my e-mail? [email protected] many thanks

[nAFaNyA]

Hiyo guys this ROM must be the best for the Imito MX2?

[aldinezi]

you downloaded the "Overclocked Kernel - 1080p (try at your own risk - CPU 1608/GPU 400/DDR 600)"? Could you send to my e-mail? [email protected] many thanks

Did you get the overclocked kernel, as my only option is to try that version... Every other ROM for mtk chipsets, works fine but without wifi, and this one Shomari's ROM is the only one that has working wifi, but crashes and screen freezes..