Binary patched kernels for Pipo models

[heisenberg]

Now I use the follwoing, which seems to be stable on my tab.

312	850
504	875
816	900
1008	1000
1200	1075
1416	1175
1704	1275

And your GPU settings:

MHz	mV
133	875
200	900
266	950
300	975
400	1025
600	1175

RAM at 720MHz - 1225mV

Everythings fine. Antutut passed. Boots fine. All right. Thanks!!!

Keep me posted for the updated Kernel.

[X-Ray]

Hi Heisenberg.
Can you upload your kernel for testing mee too plz.
thx.
Ray

[giouncino]

now I set the GPU to:

GPU
MHz	mV
133	800
200	825
266	850
300	875
400	950
600	1100

incredibly is still stable without any artifact....
they are from -150mV to an incredibly -200mV with respect to stock voltages...
fantastic results!

[heisenberg]

Hi Heisenberg.
Can you upload your kernel for testing mee too plz.
thx.
Ray

https://dl.dropboxusercontent.com/u/24735317/kernel_cpu1704h_gpu600_ddr720%20low%20GPU-Volt%20and%20CPU%20-%20925000%2C%20816000.img

CPU
[850000, 312000],
[875000, 504000],
[925000, 816000],
[1000000, 1008000],
[1075000, 1200000],
[1175000, 1416000],
[1275000, 1704000]

Remember, my Kernels are all with:
RAM
720MHz - 1225mV

And here is the last one, Giouncino was talking about with lowest GPU and my settings listed above, but also remeber, my RAM runs at 1225mV (runs stable on my tdevice):

https://dl.dropboxusercontent.com/u/24735317/kernel_cpu1704h_gpu600_ddr720%20lowest%20GPU600-1100%20and%20lowest%20CPU816-925.zip

[X-Ray]

Thank you very much Heisenberg..
Ray

[fastmediafree]

Hi

Pipo m6 pro overclocked cpu/gpu/ram kernels ? i see many thread but in someone is not clear for which model ...

if is possible too for m9 pro and m8hd,i have all three models and i can do beta tester

i did some benchmark test with stock and kasty rom for m9 pro/m6 pro/m8hd here :

http://www.wordtech.it/category/benchmark/

and i want to do the same with riley rom too

[giouncino]

Hi

Pipo m6 pro overclocked cpu/gpu/ram kernels ? i see many thread but in someone is not clear for which model ...

if is possible too for m9 pro and m8hd,i have all three models and i can do beta tester

i did some benchmark test with stock and kasty rom for m9 pro/m6 pro/m8hd here :

http://www.wordtech.it/category/benchmark/

and i want to do the same with riley rom too

all kernels posted by me are made for the M6pro. Take a look on the previous pages.

PS: I'm italian too!

[fastmediafree]

all kernels posted by me are made for the M6pro. Take a look on the previous pages.

PS: I'm italian too!

Thanks,i tried kernel_cpu1704h_gpu600_ddr720 ,good job ,i have seen this kernel is the best and stable

can you recommend one with more overclocking and that it is stable ?

i tried kernel with cpu 1.8 and gpu overclocked but doesn.t boot...

[giouncino]

Thanks,i tried kernel_cpu1704h_gpu600_ddr720 ,good job ,i have seen this kernel is the best and stable

can you recommend one with more overclocking and that it is stable ?

i tried kernel with cpu 1.8 and gpu overclocked but doesn.t boot...

You need to be very lucky if you can manage to get the CPU working at 1.8Ghz...
And as far as you say your CPU seems not lucky...

GPU overclocked how much? Keep in mind that the GPU can be overclocked on in a "predefined" steps.
over 600Mhz you can jump directly to 768Mhz and you generally need a very high voltage to get it stable (the maximum foreseen is 1.375mV, and often the GPU is still not stable).

For an everyday use I do not suggest you to overclock the GPU, the risk is to fry the tablet...
The best you can do is to undelvolt GPU and CPU as much as you can, Overclock the CPU at 1704Mhz, keep the RAM at 720Mhz, and if you're lucky you can set it to 792Mhz (even if the step 720->792 seems useless wrt performance gain).

[fastmediafree]

You need to be very lucky if you can manage to get the CPU working at 1.8Ghz...
And as far as you say your CPU seems not lucky...

GPU overclocked how much? Keep in mind that the GPU can be overclocked on in a "predefined" steps.
over 600Mhz you can jump directly to 768Mhz and you generally need a very high voltage to get it stable (the maximum foreseen is 1.375mV, and often the GPU is still not stable).

For an everyday use I do not suggest you to overclock the GPU, the risk is to fry the tablet...
The best you can do is to undelvolt GPU and CPU as much as you can, Overclock the CPU at 1704Mhz, keep the RAM at 720Mhz, and if you're lucky you can set it to 792Mhz (even if the step 720->792 seems useless wrt performance gain).

Understood,thanks for explanations,test it right then i have installed

[sebastianabate]

now I set the GPU to:

GPU
MHz	mV
133	800
200	825
266	850
300	875
400	950
600	1100

incredibly is still stable without any artifact....
they are from -150mV to an incredibly -200mV with respect to stock voltages...
fantastic results!

Do you use 300 and 400 as freqs or this is a typo?, because it seems to be a very small step from 266 to 300, and a very high step from 400 to 600.
In your original script the steps are

133
200
266
366
466
600


Is this change for a reason?

[giouncino]

Do you use 300 and 400 as freqs or this is a typo?, because it seems to be a very small step from 266 to 300, and a very high step from 400 to 600.
In your original script the steps are

133
200
266
366
466
600


Is this change for a reason?

I reverted back to the stock frequencies as soon as I realized that these are not used.
Unfortunately the only used are the frequencies foreseen in the stock kernel: 300Mhz and 400Mhz (366 ad 466 are ignored by the system).

[herrjemineh]

How do you know, which freqs are used for cpu/gpu/ram and which not?

Am Ende ist alles gut, und wenn nicht alles gut ist, dann ist es auch nicht das Ende...

[sebastianabate]

I think I'm doing something wrong here.
My Pipo M8Pro stock kernel have this GPU table

MHz mV
100 950
150 975
200 975
240 1000
300 1050
400 1100
600 1200

But when I modify the script with this table

"gpu600h" =>
[
[750000, 100000],
[775000, 150000],
[825000, 200000],
[850000, 240000],
[875000, 300000],
[950000, 400000],
[1100000, 600000]
],
the resulting kernel have this table applied

MHz mV
200 825
240 850
300 875
400 950
600 1100

the 2 first freqs are missing.

Acording to the comments inside the scripts, the replacement table must be equal or shorter than the original table, and in my case they are equals.

What am I doing wrong?

[krucifix85]

Are the voltages for those 2 figures too low?

I haven't seen others with mV lower than 800 for any figures.