CS968 MTK KITKAT ROM 4.4 - Finally

[pejochto]

No worries :-) , I´ll try to flash it with the ROM this evening, is there a preinstalled XBMC on that ROM too?

@pejochto,
There's new kitkat 4.4 ROM for MTK 20140424 link in 1st post, I've note all the changes from previous 20140419 I can find one of them is that revert back storage capacity to insternal (system) to 2GB and Sd Card (Nand Flash) to 4GB. as per your question
#1, I haven't the exact answer, IMHO, like any other system platform, the default command when their turn on, is to identify hardware In/Out and searching for driver all of that is in file system, so to speed up the access (boot time) they use dedicated partition in internal memory. Some apps need it's file system in internal as for per performance setting. You can change the SD card (Nand Flash) to Ext SD card as default nand flash, you can check here, DWYOR.
#2, Yes you can, just format your usb drive to FAT32, I'm using it too.

@servo386,
Thanks.

Hahaha.., sorry for my bad english, I mean, in new ROM (20140424) system capacity is back to 2GB (instead of 1GB in 20140419) and internal sdcard become 4GB (instead of 5,6 GB in 20140419).
Yes, I recommend to upgrade, as far as I can use, it's almost the same as 20140419. But, both KITKAT has high compatibility with XBMC, IMHO.

[pincer]

No worries :-) , I´ll try to flash it with the ROM this evening, is there a preinstalled XBMC on that ROM too?

nope, but beyond xbmc is. but, if you have problem with it, try to reinstalle it.

[pejochto]

I can now confirm that the new ROM 20140424 does make your box with 2Gb internal memory and 4Gb SD (Internal, Nand). I didnt know that different ROM could do this with the memory configuration?
But you learn something everyday thanks to the compentence of this forum.
I can also confirm that this ROM is working like a dance on CS968 version 4 board.
Thank you Pincer for all your help and for the work you do to inform us about the things we struggle with.
Super :-)

nope, but beyond xbmc is. but, if you have problem with it, try to reinstalle it.

[dio21]

Any links for the second kit kat rom
Thank you

[pejochto]

Both first and second ROM links are found on the first post of this thread.

Any links for the second kit kat rom
Thank you

[nguy]

The easiest way to know this if not, is by identify what date of firmware you currently use (from factory) (eg. 20140411 (ap6210) or 20140419 (mtk), or 20140313 (mtk) or 20140225 (mtk).

or you can try this ROM first, if the bluetooth and wifi is working, then you have mtk chips on the board, if not, then you have ap6210 chips.

Cheers,

Thanks pincer. I opened the device but couldn't find any info. If I apply this rom and the board is not MTK will this damage the box and also what would I need to flash this rom? Is is RKbatch Tool. Thanks in advance

[pincer]

Thanks pincer. I opened the device but couldn't find any info. If I apply this rom and the board is not MTK will this damage the box and also what would I need to flash this rom? Is is RKbatch Tool. Thanks in advance

1. make sure your device is CS968/ CR11s or similar, that has Quad-Core Rockchip RK3188 CPU, GPU MALI-400, 2GB RAM/ 8GB ROM and 2MP camera.
2. check this thread by brick0044, for how to look what chips of wifi and bluetooth on your board, it's place near the usb hub.
3. you can check your factory default firmware in "Setting --> About device"
4. not damage, but you will lost wireless connectivity such as wifi and bluetooth, LAN is still work though if you planning to use wired networking.
5. Yes, you need the RK Batch Tool, dont forget to install your driver with RK Driver assistant.
6. DWYOR

Cheers,

[nguy]

1. make sure your device is CS968/ CR11s or similar, that has Quad-Core Rockchip RK3188 CPU, GPU MALI-400, 2GB RAM/ 8GB ROM and 2MP camera.
2. check this thread by brick0044, for how to look what chips of wifi and bluetooth on your board, it's place near the usb hub.
3. you can check your factory default firmware in "Setting --> About device"
4. not damage, but you will lost wireless connectivity such as wifi and bluetooth, LAN is still work though if you planning to use wired networking.
5. Yes, you need the RK Batch Tool, dont forget to install your driver with RK Driver assistant.
6. DWYOR

Cheers,

Thanks. I checked brik0044 thread on found out that i've got v4 MTK. So this should hopefully work. Thanks again

[nguy]

Maybe a silly question

I've finally got my box working again and planning to flash this rom today. Pincer confirmed that RK Batch Tool is the programme to use to flash the rom which I have. I've taken a look at the program and would appreciate what steps I should take - don't want to get it wrong!

[mo123]

I've finally got my box working again and planning to flash this rom today. Pincer confirmed that RK Batch Tool is the programme to use to flash the rom which I have. I've taken a look at the program and would appreciate what steps I should take - don't want to get it wrong!

Clcik restore in the flash tool.

[nguy]

Problem

I've tried flashing this rom with the RKbatch tool. However, when I tried to flash it I got the following message "layer 58> This operation didn't do because if not supporting! Fail. Can anyone advise what this means please? I have V4 MTK box and rooted.

[pincer]

I've tried flashing this rom with the RKbatch tool. However, when I tried to flash it I got the following message "layer 58> This operation didn't do because if not supporting! Fail. Can anyone advise what this means please? I have V4 MTK box and rooted.

I'm sure you have install the driver (those your box recognized by your pc), press and hold reset button upon connecting to pc through otg usb port (near the transflash card on the box), you don't connect the power supply of the box, and the RKbatch Tool has highlighted green on some number like 5-8 or 1-2 and then you hit restore, right?
Tips, make sure the usb cable is firmly attached both on the box and the pc. try to unplug any unnecessary usb devices on your pc.

[nguy]

I'm sure you have install the driver (those your box recognized by your pc), press and hold reset button upon connecting to pc through otg usb port (near the transflash card on the box), you don't connect the power supply of the box, and the RKbatch Tool has highlighted green on some number like 5-8 or 1-2 and then you hit restore, right?
Tips, make sure the usb cable is firmly attached both on the box and the pc. try to unplug any necessary usb devices on your pc.

Hi Pincer,

The device was connected with the drivers, I did have the power plug connected though. The RKbatch tool was highlighted PINK under 5-8. I will give your instructions a try. Cheers

[nguy]

I'm sure you have install the driver (those your box recognized by your pc), press and hold reset button upon connecting to pc through otg usb port (near the transflash card on the box), you don't connect the power supply of the box, and the RKbatch Tool has highlighted green on some number like 5-8 or 1-2 and then you hit restore, right?
Tips, make sure the usb cable is firmly attached both on the box and the pc. try to unplug any necessary usb devices on your pc.

Pincer your a genius - worked like a charm

Cheers!

[pincer]

Pincer your a genius - worked like a charm

Cheers!

Genius is for Einstein, I only pass and share experiences and knowledges. Glad to help.
From the people for the people.