If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Announcement
Collapse
No announcement yet.
Announcement
Collapse
No announcement yet.
PicUntu-4.5-nand-BasicGUI installer - One file, few click install.
I just receive a MK808 Tronsmart. I tried to install picuntu 4.5.
When I connect the device I get the device ready and clear the NAND.
Then I follow flashing kernel, system and so on.
There I get a run failed and nothing.
Hopefully the device is not briked and I can flash it with the original firmware.
Can somebody tell me wher I make a mistake or what is wrong ?
Does anybody experiments such troubles ?
I just receive a MK808 Tronsmart. I tried to install picuntu 4.5.
When I connect the device I get the device ready and clear the NAND.
Then I follow flashing kernel, system and so on.
There I get a run failed and nothing.
Hopefully the device is not briked and I can flash it with the original firmware.
Can somebody tell me wher I make a mistake or what is wrong ?
Does anybody experiments such troubles ?
Thanks
See first post edit of Oct 12th re bootloader issue re MK808IV 16GB model. May also be of help to "mikeme" post 359.
*** EDIT Oct 12th *** Important for MK802IV 16gb owners.
I found out that the Mk802IV 16 gb model used to fail every-time I was trying to flash it. This was observed by other folks too. Thanks to the awesome work by Milkboy, we now have a fix for it.
Very peculiarly the 16GB model fails to flash, if you are using the Rockchip 1.20 bootloader version, you have to use Rockchip 1.24 bootloader version.
So I just got my brand new MK802IV and immediately flashed it with 4.5 (it was so easy thanks!).
The problem is my video goes black ever 10 to 15 seconds. I saw only one other person on this thread has the same issue. This is my first time in a linux environment so I don't understand what a lot of the terminal commands do or how to fix this issue.
Can anyone point me in the right direction to fix this?
I think this is the problem!
You try to use the
1. bootloader for the rk3188 (because of this, you get the timeout (can not work with rk3066))
2. rk3188-kernel at the rk3066 (this will be the next problem if you skip the first problem)
...
But where I can find the rights bootloaders, kernel and so on. On the picuntu site the links on the previous versions are dead.
And I thought that the modules were standradised for rokchips cpus.
But where I can find the rights bootloaders, kernel and so on. On the picuntu site the links on the previous versions are dead.
And I thought that the modules were standradised for rokchips cpus.
But one more problem is, that the Linux3188 at the moment does not support HW Acceleration and so I think the 4.5 at the moment is not really helpful with a 3066 Kernel, but at slatedroid there is a thread about Picuntu RC2.2 and upgraded to RC3 including the current partial Mali HW Acceleration support for the mk808...
I still haven't been able to solve the issue with the screen going black every 8 to 12 seconds. Could someone please help me out? Otherwise running linux on my device is pointless.
I don't expect any sympathy - I tried the ROM on a HX8-C which is a 3188 CS968 clone. I now have a fairly unresponsive device.
What happens is my PC does see the device through USB but the device identifies itself as VID_0000&PID_0002 so windows thinks it is a hub. No idea what is happening on the device side as there is nothing on the screen and the leds are in there usual standby state.
Tried putting a good ROM on an SD card named update.img but no luck there either
Tried shorting pins 7&8 on but the device connects anyway so it didn't make any difference. Device just connects wrong and windows tries to use its own hub drivers.
Any thoughts, tips or words of encouragement greatly received.
**** EDIT ****
Got it going - not sure which pins I was shorting in the end but held the pins shorted, press the reset button then released the pins.. tried different pins eventually it work!
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
Comment