[ROM] Unofficial OpenELEC for MK808B+ and MXQ

[PatrickJB]

I am still on 6.95.1.1 as it is working too well for me so i do not know if this happened with 6.95.1.3

__________________________________________________ ______________________________
All Black MXQ: Running MXQ.arm-6.95.1.1 On Nand. Board Number: AM_MXQ_A 20150825

I'm thinking of going back to 6.95.1.1 but wasn't that the version with the skin problems? I loose track sometimes!

-------------------------------------------------------------------------------------------------------------------------------------------
Running MXQ.arm-6.95.1.3 from Nand on all black MXQ, board number: 'AM_MXQ_A 20150825

[PatrickJB]

So just to confirm, with my device I should be using the hd builds or just a case of try both until I find one that works, assuming that one of the older builds will work?

Just found this old post and you 'may' have to set up the aml_autoscript again from what K says here: http://freaktab.com/forum/tv-player-...720#post562720

EDIT: Re-read the old post and I don't think it has anything to do with your problem!

kostaman OK, I can state that 6.95.1.1 was the build that sorted the skin problem. The builds after this had a host of changes which I'm still not sure are making my experience any better. Still unsure but will see how things pan out.

-------------------------------------------------------------------------------------------------------------------------------------------
Running MXQ.arm-6.95.1.3 from Nand on all black MXQ, board number: 'AM_MXQ_A 20150825

[jjbull]

kiwi man think the v3 board needed a different bootloader to work if you read back through this thread its mentioned somewhere i bricked a v3 board trying

[vn800art]

Trying what? If you have a V3 board as Kiwi, what's your situation atm?

[PatrickJB]

It's a pity we don't have the signature function on this board, or it's not switched on by the Admin, as it would help if everybody stated their box / board and current working build. It's a bit of a bind to keep pasting it into every post but I think it does help everyone including K see what's going on. Newbies could just scan through the thread looking for a sig with their board number etc.

I know some are not keen to open their boxes up but as long as they're careful with the wifi antenna, probably impossible to solder it back, it's not a big deal.

-------------------------------------------------------------------------------------------------------------------------------------------
Running MXQ.arm-6.95.1.3 from Nand on all black MXQ, board number: 'AM_MXQ_A 20150825

[scooter2014]

Board and photo lucky if we get right chipset lol

[scooter2014]

The Amilogic Clones are a nightmare. I currently have 4 sitting from friends ect looking for firmware for devices that actually boot.... M8 mxq111 some with writting that they are s812 but under heat sink is a s802. Ya Pcb list is in the thread and someone put effort into showing alot of them and trying to link firmware but its a great thought in one listing maybe ( Identifiy your board thread would be good to do.)

[PatrickJB]

The Amilogic Clones are a nightmare. I currently have 4 sitting from friends ect looking for firmware for devices that actually boot.... M8 mxq111 some with writting that they are s812 but under heat sink is a s802. Ya Pcb list is in the thread and someone put effort into showing alot of them and trying to link firmware but its a great thought in one listing maybe ( Identifiy your board thread would be good to do.)

Hi Scooter, As you're a Mod do you know if we can have the signature function switched on for this thread or is it not possible to turn it on for a single thread?

-------------------------------------------------------------------------------------------------------------------------------------------
Running MXQ.arm-6.95.1.3 from Nand on all black MXQ, board number: 'AM_MXQ_A 20150825

[vn800art]

And some luky ones around the world have received S812 instead of S802, I do not remember well if those were M8s ?

[scooter2014]

I speak to a few and see what best route. I like way Neomode set up forums with sections for firmware and sub areas it helps break it down better.

[VictorDUA]

kostaman
Yes. This is correct. I have (flashed) good Android rom. It has correctly working "Power Off". Then (after trying "boot from SD card method" with 6.0.3.2) I flash 6.0.3.4 to nand and everything works. "Power Off" works too. If I upgrade to 6.0.3.5 and up I lose "Power Off" function. If I revert to 6.0.3.4 my "Power Off" works again. So... Can you help ?

[PatrickJB]

I speak to a few and see what best route. I like way Neomode set up forums with sections for firmware and sub areas it helps break it down better.

Thank you!

-------------------------------------------------------------------------------------------------------------------------------------------
Running MXQ.arm-6.95.1.3 from Nand on all black MXQ, board number: 'AM_MXQ_A 20150825

[Devian]

Hi,

Nice work with the roms...
I've been using it on a black MXQ and works perfect, see there are alot of updates so will update it soon.

But i've also bought a new MXQ, this time it's the MXQ M12, which of the nand-zip files am i to use with this MXQ?
03-Apr-2016 1:59 130M OpenELEC-Amlogic.HD18Q.arm-6.95.1.3.zip
03-Apr-2016 2:00 130M OpenELEC-Amlogic.MK808B.Plus.arm-6.95.1.3.zip
03-Apr-2016 1:57 129M OpenELEC-Amlogic.MXQ.arm-6.95.1.3.zip

The model i have is this one: http://www.sunnytvtech.com/product/S...FI_Airplay.htm

Maybe this post was invisible before, as NOBODY responded, but can someone tell me if one of the NAND files is compatible and is yes, which one.
Dont want to end with a bricked device.

[PatrickJB]

Maybe this post was invisible before, as NOBODY responded, but can someone tell me if one of the NAND files is compatible and is yes, which one.
Dont want to end with a bricked device.

Try any from SD card it won't / shouldn't affect your box in any way. If it works from SD then you should be safe to install to Nand if you want a speedier experience.

EDIT: Just make sure you use the SD card versions and follow the image copy instructions which mean you need to use the Windows image utility.

EDIT 2: The versions in your post are not the SD card versions by the way!

-------------------------------------------------------------------------------------------------------------------------------------------
Running MXQ.arm-6.95.1.3 from Nand on all black MXQ, board number: 'AM_MXQ_A 20150825

[reefmonger]

I am looking at purchasing a MXQ HD18Q all black to replace my aging MX2. I love Openelec on these boxes. How is Openelec working? I have read these pages a few times but still unsure of what issues might occur. Thanks in advance for your input.

Sent from my ASUS_Z00AD using Tapatalk