[ROM] Unofficial OpenELEC for MXIII-G & Tronsmart MXIII+

[tjay78]

Howdy All,

New LibreELEC build base on kszaq 's latest release (7.0.1.1) has been uploaded - This syncs us up to the LibreELEC 7.0.1 release.

Cheers!

Hi

This build has a bug, when you run a movie with x265 codec in 1080p wont work??
x265 720p movie works fine
back to OpenELEC build

T-J@Y

[wilro_6276]

Howdy All,

New LibreELEC build base on kszaq 's latest release (7.0.1.2) has been uploaded - I've made a few minor tweaks to my patches, & have included the latest kodi 16 patches.

Cheers!

[wilro_6276]

Hi

This build has a bug, when you run a movie with x265 codec in 1080p wont work??
x265 720p movie works fine
back to OpenELEC build

T-J@Y

Hi tjay78,

I had to make a couple of 1080p x265 based files to test with With the latest release of LE (7.0.1.2), they play back as expected.

[Charbs]

Is it possible to update to a newer LE build without losing my entire setup? (non destructive update)

[ilfrance]

Is it possible to update to a newer LE build without losing my entire setup? (non destructive update)

yes just put the tar file into the .update folder and reboot

[red-i]

yes just put the tar file into the .update folder and reboot

i did this even with updating from OE to LE. it hung on the boot screen during the update but I just waited 5 mins and rebooted it via power plug and all is good.

[ilfrance]

i did this even with updating from OE to LE. it hung on the boot screen during the update but I just waited 5 mins and rebooted it via power plug and all is good.

Yes that also happened to me when I went from openelec to libre

[ilfrance]

Hi wilro, latest libreelec has a problem when using 4K resolution, previous build was fine. I've attached a picture to explain the problem

[tjay78]

Hi tjay78,

I had to make a couple of 1080p x265 based files to test with With the latest release of LE (7.0.1.2), they play back as expected.

Hi Wilro

I have researched a little ..
I have two MX3g boxes one 2g8g and the other 1g8g edition, and it seems that I only have the problem with one of the boxes, the 1g8g edition...
I do not know if it makes any sense it is the same CPU and GPU ??
Maybe it makes sense for you, or my box may be broken ...

T-J@Y

[kenmills]

Good day!

I first want to say a huge thanks to everyone involved in these ROMs, especially Wilro! You have a PM mate. :-)

Second, I would like to see if anyone has any recommendations, as I can seem to get either the OpenElec 6 or 7 builds to load on my TV box.

I have a Tronsmart MX3+ 2gb/8gb

I tried the MX3G.arm-6.0.3e, and the MX3G.arm-6.95.3a and I get the same result:

It boots up, I get the openELEC logo, and then it goes to a blank screen. I have tried going into the botloader and wiping data, but it still gives me a blank screen after the OpenElec logo.

The LibreELEC-MX3G.arm-7.0.1.2 boots up fine.

I would prefer to use OpenELEC as I have used them for a long time now, since early days.

Thanks in advance for any advice you may have.

Cheers,
Ken

[Friko]

Anyone getting 'E:cannot load volume/misc!' when going in recovery?

[red-i]

Anyone getting 'E:cannot load volume/misc!' when going in recovery?

See post 452 in this thread. I asked the same thing and wilro replied.

[Charbs]

Im kinda new to OE/LE and i see that there is a "check for updates" option in the LE settings. What will that update? Where does it check for new versions? Is that option even enabled when using these custom builds?

I would love to have OTA updates for my box if possible.

[Friko]

See post 452 in this thread. I asked the same thing and wilro replied.

Thanks for your help red-i, post 452 did not answer the question so I read the whole thread quickly.

I am confused with the filenames that are being referred to in the instructions. For e.g. I am going by the 'New Method' for dual boot.
1. Download "img.gz" file, "Image burn" it on to blank sdcard (everything on it will be wiped!)

img.gz is which file? OpenELEC-MX3G.arm-6.0.3e.img.xz? the recovery file inside the .xz file?

[erbjacob]

It boots up, I get the openELEC logo, and then it goes to a blank screen. I have tried going into the botloader and wiping data, but it still gives me a blank screen after the OpenElec logo.

The LibreELEC-MX3G.arm-7.0.1.2 boots up fine.

I would prefer to use OpenELEC as I have used them for a long time now, since early days.

You must perform a full format or use this tool to format the SD card : https://www.sdcard.org/downloads/formatter_4/ before you write OpenELEC on it.

You can use after the Win32DiskImager utility (http://sourceforge.net/projects/win32diskimager) to burn your OpenELEC image.

It worked for me...

Erbjacob