Announcement

Collapse
No announcement yet.

Announcement

Collapse
No announcement yet.

NAND Chip Mask ROM Mode Short Location

Collapse
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Originally posted by Eliminater74 View Post

    I dont have a clue what box you have or anything of the such.. so plz give us a bit more info rather then what pins to short...............
    i do not know a model. but when i do backup this is the name of backup 905X-AP6212
    atvxperience firmware is working but remote just do not work.. then i try some other rom and this happend...

    Comment


      Originally posted by Boklis View Post

      i do not know a model. but when i do backup this is the name of backup 905X-AP6212
      atvxperience firmware is working but remote just do not work.. then i try some other rom and this happend...
      Nobody.. so maybe this does not have short pins ?

      Hi, guys! Here is my android tv box from local internet and tv provider Telenet here in Riga, Latvia. It comes with shitty setup, custom firmware specifically


      this board is same

      Comment


        i find the short pins

        Hit the screwdriver all over this red circle
        You may only view thumbnails in this gallery. This gallery has 1 photos.

        Comment


          Originally posted by massoudova View Post
          Hello, I just joined you. I think my sunvell q plus was the first unbrick in the forum. Allwinner uses h6. I unbrick the box when I tried to throw Libreelec software. I would like to ask you to mark the shortpins in the photos of the board. My Regards


          Click image for larger version

Name:	sunvell board 2.jpg
Views:	5210
Size:	72.7 KB
ID:	777940
          Click image for larger version

Name:	sunvell board.jpg
Views:	5279
Size:	118.3 KB
ID:	777941

          Is there anyone who has knowledge about the subject. would ask again help.

          Comment


            Originally posted by massoudova View Post


            Is there anyone who has knowledge about the subject. would ask again help.
            try the marked area while pluggin in USB cableClick image for larger version

Name:	shortening.png
Views:	4126
Size:	196.6 KB
ID:	778752

            Comment


              thank you very much for your answer.
              Do I plug in the device or do I just plug it in via USB?

              Comment


                With male-male-USB-cable connect one male end to the box. Then while trying pins in marked area plug the other end into the pc until box is being recognized

                Comment


                  hello ..
                  I gave m8s plus DVB a wrong firmware, and it cannot boot anymore.
                  could you please help me to know which pins to short to boot it in flash mood.
                  NAND is 80G22 NW814
                  Thanks
                  I really appreciate your help ..

                  Click image for larger version  Name:	98630439953c6b489faa7e4e559cce99eb296091f7c96369c5bae89d460dbdfd600a650b.jpg Views:	0 Size:	156.0 KB ID:	779779
                  https://www.photobox.co.uk/my/photo/...d=502023494091


                  https://www.photobox.co.uk/my/photo/...d=502023489917

                  Comment


                    Hi,

                    I did a PCBA firmware upgrade on the photo and it fit Bricked my MXQ.
                    Please help me identify the pins for Mask Rom mode.
                    It does not recognize on PC usb or show video.

                    Thanks

                    Click image for larger version

Name:	image_37746.jpg
Views:	4148
Size:	105.0 KB
ID:	780335
                    Click image for larger version

Name:	image_37747.jpg
Views:	3993
Size:	99.8 KB
ID:	780336

                    Comment


                      Hi everyone,
                      just got a H96Max RK3318 today.
                      Android 9.0 4/64. True to me nature could not leave well enough alone and had to make some changes.
                      Uninstalled Prime, RKMC and another app with App Remover and rebooted.
                      Lo and behold ...bricked... well stuck in boot loop.
                      No worries going to flush this thing.... reset button inside AV not working.

                      Tried USB method... no luck
                      SD card method goes as far as restore/format SD card, but create just craps out.
                      Cannot do any of the other methods either because reset/short methods unknown.

                      Anybody know how to reset or short the NAND on this thing out
                      You may only view thumbnails in this gallery. This gallery has 3 photos.

                      Comment


                        Hi, I got this motherboard, but I can't find the model and manufacturer to download the firmware. Otherwise it's stuck on the logo..If anyone recognizes which motherboard is and what firmware it needs, I would greatly appreciate it.

                        I saw the S805 on motherboard and tried some firmware for the amlogic S805 but each stuck at 2% in the Usb burning tool.Please help.

                        Poslano sa mog Redmi Note 4 koristeći Tapatalk

                        Comment


                          Click image for larger version

Name:	mecool_km3_km9_TP.png
Views:	4767
Size:	177.9 KB
ID:	781158
                          Mecool KM3, KM9, KM9 Pro
                          Last edited by remark; 08-15-2019, 07:17.

                          Comment


                            Hi, for the chip TLIFE50..., it worked for me by cutting the pins of the image.

                            Click image for larger version

Name:	image_34886.jpg
Views:	3963
Size:	81.7 KB
ID:	781142
                            Attached Files

                            Comment


                              Originally posted by remark View Post
                              Click image for larger version

Name:	mecool_km3_km9_TP.png
Views:	4767
Size:	177.9 KB
ID:	781158
                              Mecool KM3, KM9, KM9 Pro
                              I guess there are several methods of shortening

                              Comment


                                Originally posted by soldiaz View Post

                                I guess there are several methods of shortening
                                This is more correct way. Data0 and data1 shorted. Nothing is shorted to gnd.

                                Comment

                                Working...
                                X