Beelink R89 --RK3288 Cortex-A17 Mali-T7 4Kx2K RGMII HDMI2.0 supported by ODM&developers

[adrianovalle]

Embedded Displayport 1.1

Hi! I'm very interested in the eDP capabilities (up to 4k @K 30hz). Your model of motherboard will support this connection? If yes, it's 40 pin, right? My intention is creating a portable device with a IGZO panel.
Thanks a lot!
Adriano

[bloodgnome]

AW: Beelink R89 --RK3288 Cortex-A17 Mali-T7 4Kx2K RGMII HDMI2.0 supported by ODM&developers

Two configuration:
1.2G DDR +8G Flash +Ap6210
2.2G DDR +16G Flash +Ap6335

Great.

will there be a difference in cpu speed too ? maybe a normal and a + version ?

[oman]

Hi! I'm very interested in the eDP capabilities (up to 4k @K 30hz). Your model of motherboard will support this connection? If yes, it's 40 pin, right? My intention is creating a portable device with a IGZO panel.
Thanks a lot!
Adriano

Our board is for box,NO eDP.

Great.

will there be a difference in cpu speed too ? maybe a normal and a + version ?

As far as I know,no different version.

[oman]

The last two tester are convict and mmind00,so all the testers are in.

And for other kind people who PM me for testing our R89,I appreciate all of you,Thank you..Maybe next time,we bring out some more powerful dev,you'll be in.

[adrianovalle]

Our board is for box,NO eDP.

Ok,thanks.

[leolas]

Ap6335 is my bet too, a really solid WiFi is a must be in this devices. A bad WiFi ruins the experience with a tvbox
About heat dissipation, I was obsessed always with that, thermal paste is a really good option, it will improve dissipation a lot, but a good air flow design can help a lot.

Rk3288 is raising a great expectation!

sent by my phone.
enviado desde mi teléfono.

leolas

[ssspacman]

Any idea when we testers will be sent the R89? Looking forward to testing it.

[daemonium]

i'm totally agreee with leolas, a good wifi is a must.
About the cooling, I think good air flow does more than huge copper heatsink.

[TMx]

i'm totally agreee with leolas, a good wifi is a must.
About the cooling, I think good air flow does more than huge copper heatsink.

+1 this works quite good

[oman]

+1 this works quite good

In my opinion,this ID is not friendly for me.

Check and balance for good-looking and thermal.

[TMx]

In my opinion,this ID is not friendly for me.

Check and balance for good-looking and thermal.

LOL

We are looking for the Vent holes here forget who made it

[ssspacman]

LOL

We are looking for the Vent holes here forget who made it

Oman:
Place them vertically not horizontal if you are afraid of having the same design as the competitor.

Sorry, could not resist. Point is it gives good airflow, also a few holes on the upper backside would make the airflow go through the device as warm air goes upwards.

[TMx]

Oman:
Place them vertically not horizontal if you are afraid of having the same design as the competitor.

Sorry, could not resist. Point is it gives good airflow, also a few holes on the upper backside would make the airflow go through the device as warm air goes upwards.

Air in from the bottom and Out as it is shown this photo

[ssspacman]

Yes, I also meant holes in the bottom like the competitior, also some (small) feet under the device to lift it up a few millimeters.

[ENDRJUPL]

Thank you for choosing me. I thought about:
1. The included remote control. I think it should have multimedia buttons - volume up and down, play, pause, rewind, forward, stop. If it had buttons 0-9 they could be mapped to various live TV stations in xbmc which would be great.
2. I know it's way too early for this, but if sound output (Spdif passthrough & hdmi) could be active at the same time it would be great. That way you can watch and listen to something which doesn't require great sound quality from TV's speakers and don't have to switch settings to spdif passthrough when you turn your amplifier on. I hope I'm not reinventing the wheel here. I did not see that option in any device yet. Hdmi & spdif sure, but not hdmi & spdif passthrough. If it's dumb, let me know :-) Cheers.