Cube T9 ROM/Tools/Mods, etc

[devilz-wolit]

...obviously you have selected "firmware upgrade" mode in SPFT before download....
...you use a stock rom 1.0.7 ?
you tried to use 6gb scatter ?

[Alexandr]

So I need load stock firmware with standard scatter in download mode, and after firmware upgrade with new scatter?

[devilz-wolit]

So I need load stock firmware with standard scatter in download mode, and after firmware upgrade with new scatter?

The procedures are done and written to be respected.
Here the procedure

http://freaktab.com/forum/mtk-based-devices/mtk-tablets/23135-cube-t9-rom-tools-mods-etc?p=500299#post500299

In the end, instead of restoring your backup, you can install my rom XnetfoX eXtreme 1.4b108.

[gixer]

In the end, instead of restoring your backup, you can install my rom XnetfoX eXtreme 1.4b108.

Whats the default memory partition (for apps) in your ROM.... is there an option for choosing 6gb or 8gb?

[gixer]

I checked the welds of the antenna cable (also on the mainboard) and are ok.
The black plastic where the antenna is welded inside is empty. It must be so?
In the sticky side (where there are two welds) is there any circuit that acts as antenna?
What else could you do to improve the signal reception 3G?

My Cube T9 all of a sudden recently developed exactly the same problem as you had mentioned regarding 3g signal... (strong outdoor and weak indoor) and I found out that while removing the mate film on inner lcd I accidentally losen the black wire from the second soldering point (as you can see on the photo posted by Edius the wire was soldered two times) and I simply reattached the wire firmly to these two points and now the 3G signal is as strong as before....

[devilz-wolit]

Whats the default memory partition (for apps) in your ROM.... is there an option for choosing 6gb or 8gb?

My option is 6gb but in my ROM this option is not important.

Inviato dal mio T9

[devilz-wolit]

My Cube T9 all of a sudden recently developed exactly the same problem as you had mentioned regarding 3g signal... (strong outdoor and weak indoor) and I found out that while removing the mate film on inner lcd I accidentally losen the black wire from the second soldering point (as you can see on the photo posted by Edius the wire was soldered two times) and I simply reattached the wire firmly to these two points and now the 3G signal is as strong as before....

I tried to desolder and resolder the wire from the antenna 3G but without results. Now I bought on **** a antenna 2G/3G to replace the original one. Meanwhile i asked the seller to send me to guarantee a pair of antennas 4G-2G/3G.

[onslow2630]

Hello all
I have try to install XnetfoX_14_eXtreme_b108 on my cubet9 i put it into recovery and go tu my sd2 card finf the map XnetfoX_14_eXtreme_b108 and there is no files
What do i wrong

Please help

Regards

Onslow

[devilz-wolit]

Have you expand the file RAR?

[onslow2630]

with winrar

[onslow2630]

when i have use winrar i have 11 files in folder i put that on my sd card 2

[devilz-wolit]

In this structure? RootSD/TWRP/BACKUPS/T)_MT8752/romname
and after TWRP restore ?

[onslow2630]

in recovery SDcard2 TWRP / T9_MT8752 / XnetfoX_14_eXtreme_b108 and there is no files

[onslow2630]

why can i get this on my cube

[devilz-wolit]

This recovery not work properly on T9. The correct version is 2.8.4.0!