NAND Chip Mask ROM Mode Short Location

[Roninwins]

Pin short for the a95x pro ?

[Vital]

Hello friends. Can someone help me? Tv box Docooler M9S-PRO 3 / 32gb s905x. NAND Toshiba THGBM5G8A4JBAIR http://cs5-3.4pda.to/13482168/THGBM5...db16a8ff8b4935 http://cs5-1.4pda.to/13361622/ 201807 ... 806edd2c5ed7e0 http://cs5-2.4pda.to/13361621/201807...367cc20230e1d8 http://cs5-2.4pda.to/13361620/201807...b87d9f1b8d380a

[joeching]

Can Anyone help my T95Z MAX ?
which using FORESEE NCEMASKG-16G. (Z1S1801147276-1802)
Thanks !

[robbo1829]

hi! i have a5x max+ 4g/32g Fn-Link 6222B-SRB wifi bluetooth module and did flash it on USB-4 right next to AV/reset. unfortunately, loader failed and now it is now bricked. tried the suggested short-pins but cannot detect the maskrom device. so m still looking for the correct pins to short to enter the mask mode and re-flash it. anyone knows this?

Hi the correct pins are just right of the ones you have marked. just shorten all on the right and your device will be recognized. I have done this and it works the Rockchip batch tool loaded my device.

[wackybruce]

Mecool M8S Pro+ v1.0 anyone?

I got the same version m8s pro+ v1.0, Shorting the 2 pins shown in the photo makes it connect to usb burning tool. If only I found a way to get past 4% failure with it :s

[Simonchunk]

T95Z Plus (New version) 912 2G+16G v1021

Should also work for 3G version

Pins to short are on back, shown in yellow on the blown up section

[Guest]

hi all a95x pro where short pin reset?

[Guest]

anyone help me short pin a95x pro

[xctechs]

Which pins should I short in this chip?

Chip: SanDisk SDINADF4-32G
TV Box T95Z Plus, Amlogic S912, 3GB/32GB, Wifi LTM8830

I can not boot into recovery mode.
USB Burning Tool shows errors:
[0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error
or
[0x10302001]Romcode/Switch status/Check connect/Enum device

Thanks in advance for the reply.

I have had this issue, but what I did was changed the USB port on my computer from one to another and it started to go through to 6 % and failed then i just kept trying and finally got 100%

one thing I got a say is ( once I got an in the main screen now after few seconds I get a blank screen ).

[Vital]

Hello.I opened the programUSB Burning Tool as an administrator .Android tv box not updating.Help! https://www.youtube.com/watch?v=mv0j...ature=youtu.be https://www.youtube.com/watch?v=8Hlw...ature=youtu.be Tv box Docooler M9S-PRO 3 / 32gb s905x. NAND Toshiba THGBM5G8A4JBAIR http://cs5-3.4pda.to/13482168/THGBM5...4dbf451f96edef http://cs5-1.4pda.to/13361622/201807...7354e25ce9ac51

[dragsterbox]

Hi all, I need some help to unbrick my box. Sunvell T95ZPLUS-3GB-AP6255-v1076 (32Gb)

Cannot find a rom working on it and the board is different from pictures on the forum. Cannot locate the right pin for the short.

[amlogic_user]

Hello,

Does anyone know how i can unbrick the SDMC DV8119, with the NAND chip Samsung KLM861WEPD-B031?

[flexaflex]

T95Z Plus (New version) 912 2G+16G v1021

Should also work for 3G version

Pins to short are on back, shown in yellow on the blown up section

It didn't work for me... I have the same board! v1081 firmware but no sucess to short the pin...

[elwaskop]

Hello dudes, can help me with they shorts pins to tvbox "mini m8s pro" with emmc FORESSE . please check the pictures. Thanks

[zeroprobe]

T95Z Max pin location.

Mine is 2gb / 16GB.

FYI, I had to use an older laptop with a USB 2.0 port because it was failing to flash at 2%. Now flashed OK.

Oh getting this thing open was a pain, its glued together, you need to chisel around the seal with a screwdriver,


Thanks to the guy who suggested, power the device on, load up USB burning tool, select image and click Start. Then move around shorting the points near the NAND leave it 1.5 seconds for each one. This is how I found it.