NAND Chip Mask ROM Mode Short Location

[phankhanh86]

Yes I tried that too, in fact I still leave the jumper cables that I used for shorting that 2 hole on my picture.

my process :
1. Start UBT
2.Shortpin
3 Plug power....
PC recognized
with plate mainboard have two hold near emmc....that shortpin
(my exper...)
sory my E not good

[ath156]

my process :
1. Start UBT
2.Shortpin
3 Plug power....
PC recognized
with plate mainboard have two hold near emmc....that shortpin
(my exper...)
sory my E not good

1. Try adjacent pins in the area (1) (pins 4 to 8), as this is the most probable area. After that you can try also area (2) (28 to 32 pins). Also the 2 holes (area 3) are possible and in some other cases/boards they did the trick.

2. If you have 2 spare old/useless cables you can make a DIY new USB-A/USB-A cable and very short (less than 15cm long !!). Just keep their USB-A parts and connect the 4 wires inside color to color. If your USB-A/USB-C cable you have is very long, that may be the reason why you may need additional power !! If you make a new one very short you may also try other USB ports or other laptop/PC. Not every USB port of the laptop provides the same power.
photo uploader for website

[wpra3]

1. Try adjacent pins in the area (1) (pins 4 to 8), as this is the most probable area. After that you can try also area (2) (28 to 32 pins). Also the 2 holes (area 3) are possible and in some other cases/boards they did the trick.

2. If you have 2 spare old/useless cables you can make a DIY new USB-A/USB-A cable and very short (less than 15cm long !!). Just keep their USB-A parts and connect the 4 wires inside color to color. If your USB-A/USB-C cable you have is very long, that may be the reason why you may need additional power !! If you make a new one very short you may also try other USB ports or other laptop/PC. Not every USB port of the laptop provides the same power.
photo uploader for website

Thank you so much for trying so hard to help me! I will try to make the cable and hope it will power the board with just the USB. I will report back on the result!
On side note, your E is definetly very good

[wpra3]

1. Try adjacent pins in the area (1) (pins 4 to 8), as this is the most probable area. After that you can try also area (2) (28 to 32 pins). Also the 2 holes (area 3) are possible and in some other cases/boards they did the trick.

2. If you have 2 spare old/useless cables you can make a DIY new USB-A/USB-A cable and very short (less than 15cm long !!). Just keep their USB-A parts and connect the 4 wires inside color to color. If your USB-A/USB-C cable you have is very long, that may be the reason why you may need additional power !! If you make a new one very short you may also try other USB ports or other laptop/PC. Not every USB port of the laptop provides the same power.
photo uploader for website

OMG IT WORKS THANK YOU SO MUCH!!! I'm in the brink of quitting, but your enthusiasm definetly helps me fix my board. Can't thank you enough.

For those who's on the same boat with me here's what I did wrong and what works:
1. Flashing using USB C-A works, but you definetly need usb A to A (preferably short) that will power the board via USB itself
2. Short the pin 4 and 5, counting 1 from the arrow on the bottom right.
3. Don't worry about destroying your board, I've shorted so many pins that sometimes theres a spart from shorting them, all still well

Hope this help the next user with the same problem, and once again can't thank you enough ath156

[Abdalnablse10]

Found the pins for the red pcb (clone) tx3 mini s905w 2gb 16gb (here is the url for the photo because I got blocked from uploading it here) the green line is where to short the pins. https://i.ibb.co/kxZ19sS/IMG-20200830-131514.jpg

[drukeru]

Hi all .
Please help me find pins for Beelink gt king Pro. I can't get in touch with the computer. Thanks a lot!
Unfortunately, I don't know how to upload photos

[fizzy3352]

Been looking on here for a few days Trying to find the pins to short/jump on mxq pro 4k 5g rk 3128 wifi sv6158 with the chip samsung kmk7x000vm-b314

[fizzy3352]

Been looking on here for a few days Trying to find the pins to short/jump on mxq pro 4k 5g rk 3128 wifi sv6158 with the chip samsung kmk7x000vm-b314

i
have answered this my self i think this place is great
and look forward to contributing

here is the mask rom pins if anyone else needs them

[phankhanh86]

Found the pins for the red pcb (clone) tx3 mini s905w 2gb 16gb (here is the url for the photo because I got blocked from uploading it here) the green line is where to short the pins. https://i.ibb.co/kxZ19sS/IMG-20200830-131514.jpg

how about firmware for this main board
i have board red plate v 1.2

[Hotrod1]

Do you need the factory firmware or are you looking for a custom ROM?

[phankhanh86]

Do you need the factory firmware or are you looking for a custom ROM?

anything fw to getback from the hell. sir!

[Xela67]

Hi, need help with this board it´s a Mag 410 amlogic S905X red light on.

thanks

[Onionlanky]

H
I have a tv box with the model A95X Plus TV Box Android 8,1 Amlogic S905 Y2 4 Гб DDR4 32 ГБ
Can any one help me out which pins do i need to short to get into mask mode
Regards,
BapBap 4871








Thank you in advance for your help.

Hello! Help please, need short-circuit points for these board

[Onionlanky]

Hello! Help please, need short-circuit points for these board

Asking myself: reverse board and use these points

[mumianex]

I have a tv box model H96 MAX X3 - Amlogic S905X3 Android 9.0 TV Box 4 GB RAM 32 GB ROM

Can any one help me out which pins do i need to short to get into mask mode
Nand chip is KLMBG2JENB-B041

Box is entering into boot mode by pressing "uboot button" at start but isn't detected by Amlogic USB Burning Tool and is not detected by system
I tried different versions of this app and resetting system after each install.
I tried with and without power supply, on usb 2.0 and 3.0, with different USB cables even i made my own 10cm cable - no result.

Best Regards
Paul