ATV9-MOD-(P212)AMPERE-V3

[minonano]

Realtek build is out, other builds will be updated in turn later
Good luck friends

Is Rtl same as Rtk? Thanks

[bumerc]

rtk is an abbreviation of realtek, rtl=rtk

[minonano]

bumerc, I can confirm it works on my T95m, S905X, 2+8, RTL 8723. Wifi works, did not test bluetooth, original remote works, but the added Mele F10 remote does not, I guess I have to read previounot s pages on how to. Also I have noticed that rom is not rooted, I am correct?
Please confirm, thanks for a great rom.
I forgot to mention that I cannot shut down, but it will always reboot.
Correction, I think the reason the Mele remote does not work is because both usb ports don't work, so the transmitter plug in the usb is ineffective.
So the main problem seem to be the USB ports.

[bumerc]

minonano
Hi, thanks for the report, both USB ports work on my test device, otherwise I would not have released the firmware. Plug a USB device into a non-working USB port, execute the dmesg command and send the command output in text form to me via PM.

ROM is rooted.
Shutdown must be activated in droid settings, switching off works with the original remote control

https://forum.freaktab.com/forum/tv-...569#post805569

[Falconyk]

You only need the 40183 firmware folder and dhd.ko from vendor/lib/modules. However, dhd.ko will not work with other kernels...

Folders 40183 not in your firmware

[bumerc]

and why should QCA9377 build contain the ap6330 FW? Read the first post in more detail..

[Falconyk]

and why should QCA9377 build contain the ap6330 FW? Read the first post in more detail..

Sorry, I didn’t click there))

[minonano]

minonano
Hi, thanks for the report, both USB ports work on my test device, otherwise I would not have released the firmware. Plug a USB device into a non-working USB port, execute the dmesg command and send the command output in text form to me via PM.

ROM is rooted.
Shutdown must be activated in droid settings, switching off works with the original remote control

https://forum.freaktab.com/forum/tv-...569#post805569

bumrec, I tried to reload the image again, but could not get the mask mode using the usb burning tool, then i tried to reset the box, now I am in a delema, all I am getting is a loop aroung the boot logo, wont stop or start. Also tried the sd burn, but no luck, just looping aroung the lolgo (superceleron). Any idea what went wwrong as all I did was reset (factory), thanks

[bumerc]

minonano
take a hq photo of emmc

[minonano]

minonano
take a hq photo of emmc

EMMC08G-V100, thanks

[bumerc]

short the pins 29-30 and flash the img

[sagert]

EMMC08G-V100, thanks

Using the uart adapter ,there is an instruction here on the site.

[minonano]

short the pins 29-30 and flash the img

bumrec, it worked but only if i flash the stock rom, tried flashing yours and kept getting errors(sorry i didnt sve them).
Now looking back, maybe my problem was loading your rom over the atvxperience one, instead of over the stock rom, what do you think?
Also the wifi worked immediately, so I didn't use SSH, is that ok?

[minonano]

Using the uart adapter ,there is an instruction here on the site.

Thanks sagert, luckily I didn't have too.

[bumerc]

bumrec, it worked but only if i flash the stock rom, tried flashing yours and kept getting errors(sorry i didnt sve them).
Now looking back, maybe my problem was loading your rom over the atvxperience one, instead of over the stock rom, what do you think?
Also the wifi worked immediately, so I didn't use SSH, is that ok?

it doesn't matter which ROM you have pre-installed, it is important that the options "erase flash" and erase bootloader "have been selected..