ATV9-MOD-(P212)AMPERE-V3

[firmtech]

show HQ photo of RAM

Here are a few pics, not sure what the ram chips are. Still no luck resetting, no connection to Usb Burning Tool. Board does have 8189. I will keep trying all pins. Thanks for the help.

[bumerc]

to the right of the heat sink is the RAM chip, and please also photograph the back of the circuit board

[bumerc]

Would it be ok for T95M S905X RTL8723 2+8gb, or I'm guess RTL is not ampak? Thanks

no rtl wifi support

[hannah]

Hello bumerc
Thank you for making an ATV 9 rom for s905x and wifi AP6330.
This is my TV Box: Nexbox A95X 2GB/16GB S905X WIFI AP6330

pcbboard picture: https://ibb.co/2N4sPT4

I have installed your rom.
Working: LAN, BT, 1st USB Port (and not the 2nd USB Port)
Not Working: Wifi, Remote. (I have applied your wifi fix via ssh)

Following is the work done via ssh.

```
:/vendor/etc/dropbear #
cd /vendor/etc/wifi/buildin
mount -o rw,remount /vendor
cp -a config_6330.txt config.txt
reboot
```
I note the the following: (file size is 0 byte)
```
:/vendor/etc/wifi/buildin # ls -l
-rw-r--r-- 1 root root 0 2020-04-23 21:17 config_6330.txt
```

Diagnostic output of these two commands:

```
dmesg | grep chip
dmesg | grep wifi

130|:/vendor/etc/wifi/buildin # dmesg | grep chip
[ 0.229092] Meson chip version = RevB (21:B - 82:0)
[ 1.114130] hdmitx: system: hdmitx_device.chip_type : 3
[ 1.311043] chip type:0x21
[ 9.526795] The chip is not support hevc encoder
[ 12.145603] F1 signature OK, socitype:0x1 chip:0x4330 rev:0x4 pkg:0x0
[ 12.160616] dhd_conf_set_chiprev: chip=0x4330, chiprev=4
[ 24.130867] F1 signature OK, socitype:0x1 chip:0x4330 rev:0x4 pkg:0x0

1|:/vendor/etc/wifi/buildin # dmesg | grep wifi
[ 0.000000] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 otg_device=1 reboot_mode_android=normal androidboot.selinux=permissive logo=osd1,loaded,0x3d800000,1080p60hz maxcpus=4 vout=1080p60hz,enable hdmimode=1080p60hz frac_rate_policy=1 cvbsmode=576cvbs hdmitx=,444,8bit cvbsdrv=0 irq_check_en=0 androidboot.firstboot=0 jtag=apao androidboot.veritymode=enforcing androidboot.hardware=amlogic page_trace=on androidboot.rpmb_state=0 androidboot.serialno=1234567890 androidboot.wificountrycode=US ro rootwait skip_initramfs androidboot.dtbo_idx=0 vmalloc=512m --cmdline root=/dev/mmcblk0p18 buildvariant=userdebug
[ 1.551588] wifi: power_on_pin_OD = 0;
[ 1.553995] aml_wifi wifi: [wifi_dev_probe] no power_on_pin2
[ 1.559943] aml_wifi wifi: [pwm_double_channel_conf_dt] wifi pwm dt ok
[ 1.566577] aml_wifi wifi: [pwm_double_channel_conf] wifi pwm conf ok
[ 1.573240] aml_wifi wifi: [wifi_dev_probe] dhd_static_buf setup
[ 1.593470] aml_wifi wifi: [wifi_dev_probe] interrupt_pin=487
[ 1.599375] aml_wifi wifi: [wifi_dev_probe] irq_num=0, irq_trigger_type=1
[ 1.606402] aml_wifi wifi: [wifi_dev_probe] power_on_pin=486
[ 1.612236] aml_wifi wifi: [wifi_dev_probe] clock_32k_pin=0
[ 1.618268] aml_wifi wifi: [wifi_setup_dt] wifi_setup_dt
[ 1.623703] aml_wifi wifi: [wifi_setup_dt] irq num is69)
[ 1.629216] aml_wifi wifi: [wifi_setup_dt] interrupt_pin(487)
[ 1.635181] aml_wifi wifi: [wifi_setup_dt] power_on_pin(486)
[ 11.095015] dhd_wifi_platform_load: Enter
[ 11.106263] wifi_platform_set_power = 1
[ 11.121724] aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 486
[ 11.338372] aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 486
[ 11.848538] wifi_platform_bus_enumerate device present 1
[ 12.406456] wifi_platform_set_power = 0
[ 23.073801] wl_android_wifi_on in 1
[ 23.078417] wl_android_wifi_on in 2: g_wifi_on=0
[ 23.083081] wifi_platform_set_power = 1
[ 23.092594] aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 486
[ 23.324458] aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 486
[ 24.145729] dhd_conf_read_config: Ignore config file /vendor/etc/wifi/buildin/config.txt
[ 24.148455] Final fw_path=/vendor/etc/wifi/buildin/fw_bcm40183b2.bin
[ 24.158094] Final nv_path=/vendor/etc/wifi/buildin/
[ 24.160125] Final clm_path=/vendor/etc/wifi/buildin/clm.blob
[ 24.166547] Final conf_path=/vendor/etc/wifi/buildin/config.txt
[ 24.176067] dhd_os_open_image1: /vendor/etc/wifi/buildin/fw_bcm40183b2.bin (239507 bytes) open success
[ 24.318333] dhd_os_open_image1: /vendor/etc/wifi/buildin/ is not regular file
[ 24.320016] dhdsdio_download_nvram: Open nvram file failed /vendor/etc/wifi/buildin/
[ 24.362685] wifi_platform_set_power = 0
[ 24.370452] wl_android_wifi_on: Failed
[ 24.374316] dhd_open : wl_android_wifi_on failed (-35)
[ 24.385213] wl_android_wifi_off in 1
[ 24.389470] wl_android_wifi_off in 2: g_wifi_on=0, on_failure=1
[ 24.408377] wifi_platform_set_power = 0
[ 24.420056] wl_android_wifi_off out
[ 1914.689716] wl_android_wifi_on in 1
[ 1914.689718] wl_android_wifi_on in 2: g_wifi_on=0
[ 1914.689722] wifi_platform_set_power = 1
[ 1914.689758] aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 486
[ 1914.889810] aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 486
[ 1915.535905] dhd_conf_read_config: Ignore config file /vendor/etc/wifi/buildin/config.txt
[ 1915.543429] Final fw_path=/vendor/etc/wifi/buildin/fw_bcm40183b2.bin
[ 1915.549793] Final nv_path=/vendor/etc/wifi/buildin/
[ 1915.554778] Final clm_path=/vendor/etc/wifi/buildin/clm.blob
[ 1915.560611] Final conf_path=/vendor/etc/wifi/buildin/config.txt
[ 1915.567451] dhd_os_open_image1: /vendor/etc/wifi/buildin/fw_bcm40183b2.bin (239507 bytes) open success
[ 1915.615445] dhd_os_open_image1: /vendor/etc/wifi/buildin/ is not regular file
[ 1915.617278] dhdsdio_download_nvram: Open nvram file failed /vendor/etc/wifi/buildin/
[ 1915.653663] wifi_platform_set_power = 0
[ 1915.662586] wl_android_wifi_on: Failed
[ 1915.666574] dhd_open : wl_android_wifi_on failed (-35)
[ 1915.678978] wl_android_wifi_off in 1
[ 1915.682786] wl_android_wifi_off in 2: g_wifi_on=0, on_failure=1
[ 1915.698613] wifi_platform_set_power = 0
[ 1915.707628] wl_android_wifi_off out
:/vendor/etc/wifi/buildin #
```

Please help me to have a working Wifi.

Thank you
Hannah

[hannah]

Hello bumerc

I now have rectified my mistake and copied the correct file. And wifi is NOT working

```
:/vendor/etc/dropbear #
cd /vendor/etc/wifi/buildin
mount -o rw,remount /vendor
cp -a config_6335.txt config.txt
reboot
```

corresponding dmesg output:

```
:/vendor/etc/dropbear # dmesg | grep chip
[ 0.229499] Meson chip version = RevB (21:B - 82:0)
[ 1.119001] hdmitx: system: hdmitx_device.chip_type : 3
[ 1.315935] chip type:0x21
[ 8.031783] The chip is not support hevc encoder
[ 10.696865] F1 signature OK, socitype:0x1 chip:0x4330 rev:0x4 pkg:0x0
[ 10.711865] dhd_conf_set_chiprev: chip=0x4330, chiprev=4
[ 22.352764] F1 signature OK, socitype:0x1 chip:0x4330 rev:0x4 pkg:0x0
[ 63.392345] F1 signature OK, socitype:0x1 chip:0x4330 rev:0x4 pkg:0x0
:/vendor/etc/dropbear # dmesg | grep wifi
[ 0.000000] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 otg_device=1 reboot_mode_android=normal androidboot.selinux=permissive logo=osd1,loaded,0x3d800000,1080p60hz maxcpus=4 vout=1080p60hz,enable hdmimode=1080p60hz frac_rate_policy=1 cvbsmode=576cvbs hdmitx=,444,8bit cvbsdrv=0 irq_check_en=0 androidboot.firstboot=0 jtag=apao androidboot.veritymode=enforcing androidboot.hardware=amlogic page_trace=on androidboot.rpmb_state=0 androidboot.serialno=1234567890 androidboot.wificountrycode=US ro rootwait skip_initramfs androidboot.dtbo_idx=0 vmalloc=512m --cmdline root=/dev/mmcblk0p18 buildvariant=userdebug
[ 1.556607] wifi: power_on_pin_OD = 0;
[ 1.559003] aml_wifi wifi: [wifi_dev_probe] no power_on_pin2
[ 1.564954] aml_wifi wifi: [pwm_double_channel_conf_dt] wifi pwm dt ok
[ 1.571591] aml_wifi wifi: [pwm_double_channel_conf] wifi pwm conf ok
[ 1.578232] aml_wifi wifi: [wifi_dev_probe] dhd_static_buf setup
[ 1.598470] aml_wifi wifi: [wifi_dev_probe] interrupt_pin=487
[ 1.604394] aml_wifi wifi: [wifi_dev_probe] irq_num=0, irq_trigger_type=1
[ 1.611384] aml_wifi wifi: [wifi_dev_probe] power_on_pin=486
[ 1.617276] aml_wifi wifi: [wifi_dev_probe] clock_32k_pin=0
[ 1.623280] aml_wifi wifi: [wifi_setup_dt] wifi_setup_dt
[ 1.628674] aml_wifi wifi: [wifi_setup_dt] irq num is69)
[ 1.634280] aml_wifi wifi: [wifi_setup_dt] interrupt_pin(487)
[ 1.640197] aml_wifi wifi: [wifi_setup_dt] power_on_pin(486)
[ 9.700867] dhd_wifi_platform_load: Enter
[ 9.709944] wifi_platform_set_power = 1
[ 9.719185] aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 486
[ 9.927824] aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 486
[ 10.441619] wifi_platform_bus_enumerate device present 1
[ 10.952548] wifi_platform_set_power = 0
[ 21.399190] wl_android_wifi_on in 1
[ 21.402945] wl_android_wifi_on in 2: g_wifi_on=0
[ 21.407621] wifi_platform_set_power = 1
[ 21.416909] aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 486
[ 21.636701] aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 486
[ 22.368021] dhd_os_open_image1: /vendor/etc/wifi/buildin/config.txt (47 bytes) open success
[ 22.400056] Final fw_path=/vendor/etc/wifi/buildin/fw_bcm40183b2.bin
[ 22.401028] Final nv_path=/vendor/etc/wifi/buildin/
[ 22.406066] Final clm_path=/vendor/etc/wifi/buildin/clm.blob
[ 22.413272] Final conf_path=/vendor/etc/wifi/buildin/config.txt
[ 22.423649] dhd_os_open_image1: /vendor/etc/wifi/buildin/fw_bcm40183b2.bin (239507 bytes) open success
[ 22.566834] dhd_os_open_image1: /vendor/etc/wifi/buildin/ is not regular file
[ 22.568538] dhdsdio_download_nvram: Open nvram file failed /vendor/etc/wifi/buildin/
[ 22.606024] wifi_platform_set_power = 0
[ 22.614048] wl_android_wifi_on: Failed
[ 22.617923] dhd_open : wl_android_wifi_on failed (-35)
[ 22.630510] wl_android_wifi_off in 1
[ 22.634135] wl_android_wifi_off in 2: g_wifi_on=0, on_failure=1
[ 22.650001] wifi_platform_set_power = 0
[ 22.659016] wl_android_wifi_off out
[ 62.190715] wl_android_wifi_on in 1
[ 62.194781] wl_android_wifi_on in 2: g_wifi_on=0
[ 62.201102] wifi_platform_set_power = 1
[ 62.209324] aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 486
[ 62.495221] aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 486
[ 63.506758] dhd_os_open_image1: /vendor/etc/wifi/buildin/config.txt (47 bytes) open success
[ 63.506815] Final fw_path=/vendor/etc/wifi/buildin/fw_bcm40183b2.bin
[ 63.506817] Final nv_path=/vendor/etc/wifi/buildin/
[ 63.506818] Final clm_path=/vendor/etc/wifi/buildin/clm.blob
[ 63.506820] Final conf_path=/vendor/etc/wifi/buildin/config.txt
[ 63.508153] dhd_os_open_image1: /vendor/etc/wifi/buildin/fw_bcm40183b2.bin (239507 bytes) open success
[ 63.673381] dhd_os_open_image1: /vendor/etc/wifi/buildin/ is not regular file
[ 63.673386] dhdsdio_download_nvram: Open nvram file failed /vendor/etc/wifi/buildin/
[ 63.673659] wifi_platform_set_power = 0
[ 63.673664] wl_android_wifi_on: Failed
[ 63.673668] dhd_open : wl_android_wifi_on failed (-35)
[ 63.673679] wl_android_wifi_off in 1
[ 63.673681] wl_android_wifi_off in 2: g_wifi_on=0, on_failure=1
[ 63.673798] wifi_platform_set_power = 0
[ 63.673802] wl_android_wifi_off out
:/vendor/etc/dropbear #
```

Thank you in advance.
Hannah

[alex161rus]

delete

[alex161rus]

Not Working:Remote.

replace file for nexbox s95x
/vendor/etc

[hannah]

replace file for nexbox s95x
/vendor/etc

--------------------------------------

```
hannah@DESKTOP-00V2F0C:/mnt/c/opt/rom/ATV9-IMG-DEBUG-AMPERE-V3$ scp -i id_rsa remote_ir_nexbox_a95x_s905x/remote1.tab [email protected]:/vendor/etc
#################################
* * * * * * * * * * * * * * * * *
* Welcome to ampere SSH-server! *
* *
* * * * * * * * * * * * * * * * *
#################################
sh: scp: not found
lost connection
````

scp is failing to copy as it does not exist in the tvbox. Perhaps I need to push it via adb.
Shall try later.

Wifi is NOT working.

Thanks
Hannah

[bumerc]

You have to remount the vendor partition with rw, write access:

mount -o rw,remount /vendor

[bumerc]

As for ap6330, it was not buildin wifi and was optionally added. The nvram file is not loading at the moment, I have to find out why

EDIT: I found the bug, but this requires full recompilation of the kernel and wifi drivers. If I find time, I try to fix this

[hannah]

As for ap6330, it was not buildin wifi and was optionally added. The nvram file is not loading at the moment, I have to find out why

Okay thanks. I appreciate your effort and patiently waiting.

[hannah]

At this stage only Wifi NOT working.

replace file for nexbox s95x
/vendor/etc

Your remote1.tab file is pushed via adb and the remote is working now. Thank you.

Here are the commands run via adb:

C:\opt\adb>adb connect 192.168.0.101:5555
C:\opt\adb>adb root <------------- must start adb as root otherwise all below commands will fail
C:\opt\adb>adb shell mount -o rw,remount /vendor
C:\opt\adb>adb push remote1.tab /vendor/etc
remote1.tab: 1 file pushed. 0.1 MB/s (2143 bytes in 0.033s)

[alex161rus]

As for ap6330, it was not buildin wifi and was optionally added. The nvram file is not loading at the moment, I have to find out why

EDIT: I found the bug, but this requires full recompilation of the kernel and wifi drivers. If I find time, I try to fix this

can add qc9733 to the kernel? then all s905x boards will be supported. It will be great.

[freakbox]

can add qc9733 to the kernel? then all s905x boards will be supported. It will be great.

Please add ? and repair my Bluetooth please ? i will test it when you make it

[dsm150]

EDIT: I found the bug, but this requires full recompilation of the kernel and wifi drivers. If I find time, I try to fix this

We are gratefully waiting for the updated firmware