OpenELEC for s82, M8, MXIII, Tronsmart S89

[zambu]

...//amlinux.ru/target/?C=M;O=D

check this one have installed it in my mx3 1g working OK some bugs that it is only a version test

[e123enitan]

Just a quick question, any plan OpenElec 6 beta 2, can one of the developer treat us to this new gooddy, I have heard from friends using Kodi 15, that is perfromace is noticeable .
Cheers!

[SilverNerfer]

Hi All
I have what appears to be an MX3 however when I load OpenElec 5.0.8 there is no wifi (I have tried turning off wired) and no bluetooth, apart from that all works well
The board in the device is marked MX3-M82-v3.1 and on board appears to be a chip marked AP6234 which I assume is the 6234 WiFi/Bluetooth chip.
Is there any way to load a driver for this chip ?
Thanks in advance

[Kezz]

Sometimes when you are uploading the MX with Openelec it is best to do a reset a couple of times with the toothpick then pull the power and begin the upload I sometimes upload it twice back to back and that seems to solve the problem!!! Good Luck!!!

[backintheday]

Ill try that. Kezz but when its in openelec 5.0.8 the light turns red with no on /off and remote doesnt work at all and I've tried 5.0.8 for s82.

[Kezz]

MX3 For those who have problems with Openelec 5.0.8 WIFI...I have run into this and the way I fixed it was to go to Settings....openelec .....Network and tun OFF the Wired connection and turn on The WiFI...then all works very well!!! Hope this helps!

[Ichijoe]

ya nothing is working to get openelec with wifi i even went to mxIII plus 202 hoping wifi would kick in but no luck . kinda fd thinking of tronsmart img 06032015 trying now. any help

Isn't the MXIII Plus just a rebranded Minix Neo x8 Plus? Without the External Antenna? e.g. An Amlogic S812 SoC with 2G RAM, and whatever on shared Storage?! 'Cause I'm fairly sure the MXIII, and the Tronfy MXIV are, just simply S812 SoC Devices... So it seems to me that the Neo x8 Version of OpenELEC would be the correct One to use in this instance. Since neither the MXIII Plus, nor the TronFY MXIV are actually related to the MXIII S802 SoC designs.

Thus why you have 202k4 Firmware (IIRC), AND NOT 11xk4 Firmware.11xk4 are for K200 devices such as the M8, S82, S89, or the MXIII (M82), which again should all be S802 SoC Devices.

[backintheday]

ya nothing is working to get openelec with wifi i even went to mxIII plus 202 hoping wifi would kick in but no luck . kinda fd thinking of tronsmart img 06032015 trying now. any help

[backintheday]

So openelec 5.0.8 - 5.0.0 has no wifi working. going to try stock fw to see if i can get it back because 111k4 wifi will not turn on as well do you think this mxIII 2g has a new wifi adapter ? never had this happen. it was on 115k4 out of the box im looking for the right stock one and going to give it a go. thanks .

[backintheday]

Ill change it and see . Thanks so much

[Kezz]

I used the openelec-amlogic.s82.arm-5.0.8.zip and I used Zip to Extract it....Rar and Izarc did not extract it correctly and I have installed this successfully to 4 Boxes!

[backintheday]

So i have mxIII 2g that i have running openelec 5.0.0 work great but i just bought another one and in recovery it says wrong footing . recovery is the newest KOT49H 20150518 has a newer google slash screen i tried the latest 5.0.8 and still nothing . Has anyone had this going on with them .

[Veronica]

I'm going to give this try. Is 5.0.8 worth it or i rather use an older build?. what version to start

[FrankTank]

Thanks for this, thought I would post my solution to use the standard remote that comes with the MXIII unit, not sure if this is common knowledge or been uploaded, couldn't find it, I used another thread to get an almost complete working remote that comes supplied with the unit, running openelec. Mouse function not working atm todo

credit to cde:

http://freaktab.com/forum/tv-player-support/amlogic-based-tv-players/tronsmart-aml-devices/9997-prometheus-universal-remote-setup-for-any-amlogic-board-with-ir/

ssh to unit
Login:root
Passwordpenelec

cd /storage/.config
vi remote.conf
select text and copy command on keyboard eg. command+c on mac ctrl+c win
press i for insert in vi
use paste command on keyboard
:wq! (write/quit)
chmod 644 remote.conf
remotecfg remote.conf

should output

OpenELEC:~/.config # remotecfg remote.conf
curpara:factory_code 7f800001
curpara:work_mode 00000000
curpara:repeat_enable 00000001
curpara:release_delay 00000079
curpara:debug_enable 00000001
curpara:reg_control 000fbe40
KEYMAP_LEVEL: ircode = 0x51, keycode = 116
KEYMAP_LEVEL: ircode = 0x4d, keycode = 66
KEYMAP_LEVEL: ircode = 0x9, keycode = 416
KEYMAP_LEVEL: ircode = 0x11, keycode = 404
KEYMAP_LEVEL: ircode = 0x54, keycode = 197
KEYMAP_LEVEL: ircode = 0x4f, keycode = 14
KEYMAP_LEVEL: ircode = 0x56, keycode = 74
KEYMAP_LEVEL: ircode = 0xbd, keycode = 51
KEYMAP_LEVEL: ircode = 0xbb, keycode = 52
KEYMAP_LEVEL: ircode = 0x4e, keycode = 78
KEYMAP_LEVEL: ircode = 0x53, keycode = 102
KEYMAP_LEVEL: ircode = 0x1b, keycode = 14
KEYMAP_LEVEL: ircode = 0x26, keycode = 103
KEYMAP_LEVEL: ircode = 0x25, keycode = 105
KEYMAP_LEVEL: ircode = 0xd, keycode = 28
KEYMAP_LEVEL: ircode = 0x27, keycode = 106
KEYMAP_LEVEL: ircode = 0x28, keycode = 108
KEYMAP_LEVEL: ircode = 0x49, keycode = 23
KEYMAP_LEVEL: ircode = 0x52, keycode = 272
KEYMAP_LEVEL: ircode = 0x31, keycode = 2
KEYMAP_LEVEL: ircode = 0x32, keycode = 3
KEYMAP_LEVEL: ircode = 0x33, keycode = 4
KEYMAP_LEVEL: ircode = 0x34, keycode = 5
KEYMAP_LEVEL: ircode = 0x35, keycode = 6
KEYMAP_LEVEL: ircode = 0x36, keycode = 7
KEYMAP_LEVEL: ircode = 0x37, keycode = 8
KEYMAP_LEVEL: ircode = 0x38, keycode = 9
KEYMAP_LEVEL: ircode = 0x39, keycode = 10
KEYMAP_LEVEL: ircode = 0x58, keycode = 1
KEYMAP_LEVEL: ircode = 0x30, keycode = 11
KEYMAP_LEVEL: ircode = 0x44, keycode = 111
MOUSEMAP_LEVEL: ircode = 0x0, keycode = 198
MOUSEMAP_LEVEL: ircode = 0x1, keycode = 209
MOUSEMAP_LEVEL: ircode = 0x2, keycode = 213
MOUSEMAP_LEVEL: ircode = 0x3, keycode = 144
work_mode = 0
repeat_enable = 0x1
factory_code = 32640
release_delay = 0x79
debug_enable = 0x1
reg_control = 1031744


then reboot and play


<<COPY BELOW - do not copy this line

# ZAP-A10 NEC remote
factory_code = 0x7f800001
work_mode = 0
repeat_enable = 1
release_delay = 121
debug_enable = 1
reg_control = 0xfbe40

key_begin
0x51 116 ;POWER
0x4d 66 ;MUTE
0x09 416 ;MEDIA
0x11 404 ;MUSIC
0x54 197 ;WEB
0x4f 0x0E ;APP
0x56 74 ;VOL-
0xbd 0x33 ; 105 ;REW
0xbb 0x34 ; 106 ;FFW
0x4e 78 ;VOL+
0x53 102 ;HOME
0x1b 14 ;RETURN
0x26 103 ;ARROW_UP
0x25 105 ;ARROW_LEFT
0x0d 28 ;OK
0x27 106 ;ARROW_RIGHT
0x28 108 ;ARROW_DOWN
0x49 0x17 ;46 ;MENU
0x52 0x110 ;MOUSE
0x31 2 ;1
0x32 3 ;2
0x33 4 ;3
0x34 5 ;4
0x35 6 ;5
0x36 7 ;6
0x37 8 ;7
0x38 9 ;8
0x39 10 ;9
0x58 0x01 ;;;; ;1/a
0x30 11 ;0
0x44 111 ;DEL

key_end


mouse_begin
0x00 0xc6 ; mouse move up
0x01 0xd1 ; mouse move down
0x02 0xd5 ; mouse move left
0x03 0x90 ; mouse move right
mouse_end

<<COPY END - do not copy this line

[MikeD]

Yes, looks like that one has some kind of dualboot.
But the other link was just a normal M8 box. I don't think they use same software.