Pipo M9 Pro RileyROM 1.7

[Nordo]

Can someone give me a guide to running Antutu?
Does the benchmark that everyone quotes include the 3D test?
Cheers

[rrileypm]

Antutu is pretty straight forward. Just open the app and touch run test. It just does everything, and gives you a graph at the end, comparing your device with other models.

If you truly want an accurate reading, run it multiple times and average them.

[BillinCA]

I found my scores impacted by having other running apps, but most noticeably jump from 17.1k to 18.8k when I disconnected the HDMI cable before the test. That resticted it to landscape mode - it must cost to duplicate to the external display. Lots of reasons possible for varied scores - lots of other activity that you don't have obvious control over.

[Nordo]

Antutu is pretty straight forward. Just open the app and touch run test. It just does everything, and gives you a graph at the end, comparing your device with other models.

If you truly want an accurate reading, run it multiple times and average them.

Thanks, mate!
I ran Antutu and ended up with the graphs, but couldn't figure out where to read to overall numeric rating.

[griff2]

Thanks, mate!
I ran Antutu and ended up with the graphs, but couldn't figure out where to read to overall numeric rating.

I'm no expert, but if it is a bar chart graph you end up with - one of those horizontal bars is titled something like 'your device' and that's the figure for your Pipo device.

Best wishes from France.

[BillinCA]

When I run it, the overall score is on the Bar Chart line for
My Device: 18xxx
which appears below Nexus 10 and above Galaxy S3.

If I select the three horizontal lines in the top left corner (below notifications), History will give you the individual scores for test components (and you can slide through various test runs).

[griff2]

When I run it, the overall score is on the Bar Chart line for
My Device: 18xxx
which appears below Nexus 10 and above Galaxy S3.

If I select the three horizontal lines in the top left corner (below notifications), History will give you the individual scores for test components (and you can slide through various test runs).

Thank you for that info.

[Nordo]

Thank you for that info.

+1.

[rrileypm]

Wow...almost 11,000 views on this thread...VERY COOL!!!!!!!!

[ANDever]

Hi. I have installed the 1.7B version of Your firmware. Much better than stock. Wifi is more stable also. I have disassembled my M9 PRO 3G, and moved the WiFi antenna to different place inside of the tablet, now the signal is even stronger but i would suggest to take a closer look on that wifi driver.. i think it is faulty. Sometimes it just looses the signal. Then i have to turn it off and on again. Sometimes few times before it connects again. It happens no matter if im close to the router or on a bigger distace. Still the same problem. The reason i have looked inside of that tablet was because i cannot make a GPS connection to ANY satellite at all. So as a gps navigation this tablet is useless.. I cannot even locate that antenna inside of the device.

Also another notice from me - with bootanimation.zip deleted, this tablet boots a little faster.

Thanx for that firmware anyway mate! It is much better than few other that i have tested.

Also i think i should mention that i have not seen any OTA update notifications at all on 1.7B
Everything works fine. Except that GPS signal and WiFi

[Nordo]

Wow...almost 11,000 views on this thread...VERY COOL!!!!!!!!

[Nordo]

Hi. I have installed the 1.7B version of Your firmware. Much better than stock. Wifi is more stable also. I have disassembled my M9 PRO 3G, and moved the WiFi antenna to different place inside of the tablet, now the signal is even stronger but i would suggest to take a closer look on that wifi driver.. i think it is faulty. Sometimes it just looses the signal. Then i have to turn it off and on again. Sometimes few times before it connects again. It happens no matter if im close to the router or on a bigger distace. Still the same problem. The reason i have looked inside of that tablet was because i cannot make a GPS connection to ANY satellite at all. So as a gps navigation this tablet is useless.. I cannot even locate that antenna inside of the device.

Also another notice from me - with bootanimation.zip deleted, this tablet boots a little faster.

Thanx for that firmware anyway mate! It is much better than few other that i have tested.

Also i think i should mention that i have not seen any OTA update notifications at all on 1.7B
Everything works fine. Except that GPS signal and WiFi

Hi
You wouldn't like to do a little YouTube video with a link here on how you opened the tablet and moved the antenna?

[Kastrup]

Feadback on 1.7a

Hello Riley,
Thanks for your work on this release!
I received my new M9Pro several days ago and sent right to the 'operation room'.
Glad to inform you the 1.7a operation went through fine and the patient (i.e. M9Pro) is in great shape as all works well after first attempt.

However, I have a question:
How do I reclaim more space from the internal storage as it still shows 2Gb while there must be a few free tons available...?
Thanks
/Kastrup

[tkfkdgo]

Anyone else having 'noise' on high res hdmi?

Sent from my M9 pro (20130822) using Tapatalk4

[Nordo]

Hello Riley,
Thanks for your work on this release!
I received my new M9Pro several days ago and sent right to the 'operation room'.
Glad to inform you the 1.7a operation went through fine and the patient (i.e. M9Pro) is in great shape as all works well after first attempt.

However, I have a question:
How do I reclaim more space from the internal storage as it still shows 2Gb while there must be a few free tons available...?
Thanks
/Kastrup

Read the Beginners instructions that came with the ROM.
It explains how to use install different "Parameters" which will give you different free storage.
The recommended "parameter" is 6GB. i.e change the "parameter6gb" to "parameter" by simply using Rename (and change "parameter" to "parameter2gb").
The batch tool will only install the parameter.img that's called "parameter.img"

Does that make sense?