Binary patched kernels for Pipo models

[r0llingmuffin]

... ok .... I'm embarrassed ... sorry ... i thought that I'd see the kernel custom version on menu settings ..... again .... I'm sorry for troubling you all ....

now i get a 21.294 on Antutu .....

[giouncino]

You don't need USB debugging checked. If your tablet is still booting ok run CPU spy app to check kernel

Sent from Tapatalk on my m6pro running Riley ROM 1.8 KK

not completely true:
with CPU spy you will see 1.7Ghz if you use a kernel with higher frequency.
Otherwise nothing is visible from CPU Spy.

Make a test with antutu: with ANY of my modified kernels will go over 20.000points.
The stock kernel is always below that.

[giouncino]

do i use the "Nfs menu" or the "Flash menu" for flashing custom kernel?

hey!
read post #513!!!

Everything you did is correct!

[r0llingmuffin]

hey!
read post #513!!!

Everything you did is correct!

ok .... I'm sorry .... i get a 21.294 in Antutu ..... thank you and I really am embarrassed ....

[Billcnz]

Switched from claro to low_v2 and speed and stability still good, thanks giouncino. Also tested flashing using flash_image binary directly on device and also works fine.

Sent from Tapatalk on my m6pro running Riley ROM 1.8 KK

[fazerg]

kernel version in settings remains as 3.4.0 york@mid-Porsche Thu Feb 13 10:03:19 CST 2014.

It will stay the same as script is not changing anything but freg/volt tables. The only way is to check available frequencies/voltages with third party software or adb(or android terminal emulator)+dmesg to detect if mod kernel is working.

[claro966]

Hi giouncino,
Back again after some time for job reasons.

Thank you for the customed kernels for RR1.8!!!!

I will install both tomorrow... :-)

Inviato dal mio M6pro utilizzando Tapatalk

[giouncino]

Hi giouncino,
Back again after some time for job reasons.

Thank you for the customed kernels for RR1.8!!!!

I will install both tomorrow... :-)

Inviato dal mio M6pro utilizzando Tapatalk

Welcome back!
Let me know if customized kernel for kitkat is good for you too!

[fokemon]

Damn... I installed KK at last, now that GPS works with it. After flashing new kernel, Navionics doesn't work anymore, but stops at the start. It worked ok with 1.8 package kernel. Could it be the kernel, or just app problem? Antutu with package kernel was 17000, with these in page 24 more than 20000. I would like to keep it that way...

[giouncino]

Damn... I installed KK at last, now that GPS works with it. After flashing new kernel, Navionics doesn't work anymore, but stops at the start. It worked ok with 1.8 package kernel. Could it be the kernel, or just app problem? Antutu with package kernel was 17000, with these in page 24 more than 20000. I would like to keep it that way...

I don't think it's due to custom kernel,but try flashing back stock kernel and let US know!

[fokemon]

I don't think it's due to custom kernel,but try flashing back stock kernel and let US know!

Do you mean one in Randy's package, or factory stock?

[giouncino]

Do you mean one in Randy's package, or factory stock?

The one included in RileyRom 1.8

[Buskavar]

Gionuncino: Your kernel works like a charm!

I just want you to know that the kernel_kitkat_1.8_cpu1704h_gpu600h STOCK_ddr720_VERY_LOW_V2 seems to work very stable on my M6pro with Kitkat 1.8! I haven't had it for more then 4-5 hours so I can't say anything about the battery yet but it's stable and the Antutu value raised from 19566 to 20944.

[Janne]

Boot problem!

I flashed very low v2 kernel for RR 1.8 and now the tablet wont boot. I only see rileyrom logo for a few seconds and after that screen goes black. No luck either trying to get it back into flash mode. Tried removing sd-card and sim-card, nothing.

Any solutions? Before that RR 1.8 was running ok.

Janne

[Janne]

I flashed very low v2 kernel for RR 1.8 and now the tablet wont boot. I only see rileyrom logo for a few seconds and after that screen goes black. No luck either trying to get it back into flash mode. Tried removing sd-card and sim-card, nothing.

Any solutions? Before that RR 1.8 was running ok.

Janne

Got it to work, don't really know how or why, but after a brief charge I pressed the power button for like the millionth time and it booted and I managed to flash the Claro kernel! I also popped in and out the sd- and sim-cards several times in the process...

Anyways I'm so reliefed because it's my wife's tablet and I already thought I bricked it...

Janne