If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Announcement
Collapse
No announcement yet.
Announcement
Collapse
No announcement yet.
[ROM] Mecool M8S PRO+ TVStock Nexus ROM (Android TV 7.1)
The version running in my BOX is 20170825. Should I install this lastest version same as first time, with factory reset, etc? Or should I go for the 0930 version first?
This new one (1001), if I understood right, have the drivers for dualshock3?!
Hi everyone, i already flash my MecoolM8S pro+ last month with firmware OTA (20170825). What is the procedure for updating? OTA or full flash? Where is OTA option in the nexus rom if we have already flash it? Thank you
As I say in the OP, the updater is signed, and so can be installed in the Update app, the stock recovery, or TWRP. Since you don't have the Mecool Update app anymore, just install it in recovery.
To enter recovery (stock or TWRP), type "reboot recovery" from the Terminal app. When TWRP comes up, swipe to enter, click Install, select your source (SD card, USB flash drive, etc.), select the update .zip file, and then swipe to install. After that, you can optionally do a data wipe (factory reset) using the Wipe command.
If you've got stock OEM recovery, select "Apply update from EXT", select your source, and then select the update .zip file. After that, you can optionally do a factory wipe.
As I say in the OP, the updater is signed, and so can be installed in the Update app, the stock recovery, or TWRP. Since you don't have the Mecool Update app anymore, just install it in recovery.
To enter recovery (stock or TWRP), type "reboot recovery" from the Terminal app. When TWRP comes up, swipe to enter, click Install, select your source (SD card, USB flash drive, etc.), select the update .zip file, and then swipe to install. After that, you can optionally do a data wipe (factory reset) using the Wipe command.
If you've got stock OEM recovery, select "Apply update from EXT", select your source, and then select the update .zip file. After that, you can optionally do a factory wipe.
Followed everything, and then the update apparently was ok. When rebooted, it keeps freezing in the NEXUS initial screen... and don't go any further. I cant even do a hard reset... it freezes directly in NEXUS screen.
I just installed the update here and it worked fine. Do you by chance have one of the bad batch with the Samsung eMMC 5.1 chipset (KLMAG1JENB - B041)? See scary BIG RED WARNING at the top of this topic for more details.
I got SEC 713 are all of these faulty or just some? I had no crashes on mine on default firmware but I want to flash ATV , is there way to test ..maybe copy something to fill up all the flash see if can copy back?
As mentioned previously, My eMMC is SEC 649 B041 (my build is20170815.182813.V0321)
I just did the OTA UPDATE 20171001.
Unfortunately...it hasn't worked....it's stuck on "MECOOL" screen.
Therefore...if nothing can be done to save this box....I might as well get some pleasure in putting my hammer on it ...
As mentioned previously, My eMMC is SEC 649 B041 (my build is20170815.182813.V0321)
I just did the OTA UPDATE 20171001.
Unfortunately...it hasn't worked....it's stuck on "MECOOL" screen.
Therefore...if nothing can be done to save this box....I might as well get some pleasure in putting my hammer on it ...
There is a good chance you will be able to revert it back to the original firmware, by downloading it and burning it using the burning tool. You may have to enter NAND mask ROM mode to get the burning tool to see the box
My friend has sec 713, (klmag1jenb=eMMC 5,1) and he was upload file v0321_tvstock-20170825 without any problems...
My box has sec 652 (klmag1jenb=eMMC 5,1) and I was bricked my box after updating file v0321_tvstock-20170825...
According to tv box Z69 (Pins are same on eMMC) from this link : http://freaktab.com/forum/main-categ...310#post673310
Below I attached new proposal...for test - short 2 pins on underside of board - do not solder them, just short circuit while attaching USB
Thanks for the new update. Here are my experiences so far:
- After applying OTA update via TWRP, the box got stuck at Nexus Logo.
- But still can use burning tool to flash img file with success.
- I can root supersu via the updated TWRP so that I can use dynamic refresh rate with SPMC
- Sadly, when SPMC trying to change refresh rate I always get the black screen. It seem the box did change refresh rate. Audio still get through hdmi port but no picture.
Anyway, it's good to see the new update coming to this box.
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
Comment