Mecool M8S PRO L 4K TV Box Amlogic S912 Bluetooth 4.1 + HS

[drmhussein85]

But Guest i already tried to use USB Burning Tool and shunt the reset pins but nothing happens and there's no diference because the USB Burning Tool recognises the box. I've tried to flash this firmware "M8S_PRO_L-V0928_TVStock-20180109", also this one: "M8S_PRO_L-NHG47L-20171216.102705.V0928" and also this one: "M8S_PRO_L-V0928_TVStock-20171202" and the result is allways the same when i hit enter:

ERROR At 2% when i'm not using power cable
http://prntscr.com/i3pblz

ERROR at 7% when i'm using both power cable and USB male to male:
http://prntscr.com/i3pbxj
PS: I've tried with the latest USB Burning Tool and this 2.0.5.15 version

Do you got the correct .img files to restore my bootloader because i perhaps might screwed it (i don't know whatelse to do)

just follow the method I talked about earlier.. press the recent apps button many times while pluging the power.. am sure it will work.. just don't forget to rename the recovery file to recovery.img and put it on the SD card.

it worked for me many times.

[rimasi98]

Ok Guest i tried shorting the 6-7 pin, 7-8 pin, the 17-18 pin counting left side (as you said it works on your Mecool M8S Pro) and i did it with power cable + USB male to male... Also recognises by the USB burning tool but gives me the same error:

[rimasi98]

just follow the method I talked about earlier.. press the recent apps button many times while pluging the power.. am sure it will work.. just don't forget to rename the recovery file to recovery.img and put it on the SD card.

it worked for me many times.

I've tried it many times, also with the menu button to.

The result was allways the blue LED light and a black screen... I've putted the twrp i've shown you and also many others... I think my bootloader is messed up, i don't know if yours were to.

[drmhussein85]

I've tried it many times, also with the menu button to.

The result was allways the blue LED light and a black screen... I've putted the twrp i've shown you and also many others... I think my bootloader is messed up, i don't know if yours were to.

just give it last shot using this version of TWRP

http://freaktab.org/a2346c32352b64d3

[rimasi98]

just give it last shot using this version of TWRP

http://freaktab.org/a2346c32352b64d3

I got it recorded, see if i'm doing something wrong:

https://www.youtube.com/watch?v=9lru7ZjMqhE

The recovery image is that file you gave me:

http://prntscr.com/i3yb8y

[P.X]

I got it recorded, see if i'm doing something wrong:

https://www.youtube.com/watch?v=9lru7ZjMqhE

The recovery image is that file you gave me:

http://prntscr.com/i3yb8y

Wrong.
You have to press and Hold the button while you put the power plug into the box (or switch the mains on)
This never worked for me and more reliable is short switch pins while inserting power plug and keep shorted for at least 7 seconds.
(Left front switch pin to right pin)

[rimasi98]

Wrong.
You have to press and Hold the button while you put the power plug into the box (or switch the mains on)
This never worked for me and more reliable is short switch pins while inserting power plug and keep shorted for at least 7 seconds.
(Left front switch pin to right pin)

I've tried now to press and hold while i powered it on but the result was the same.

Ok i'll give it one last try to the main reset pins:

http://prntscr.com/i3yq7f

[rimasi98]

P.X here you have at i've done and the result:

https://www.youtube.com/watch?v=f3rWZd7AgG4

I also tried to short pins on the eMMC and the result is allways the same:

[P.X]

P.X here you have at i've done and the result:

https://www.youtube.com/watch?v=f3rWZd7AgG4

That looks like the right method now.
Can't read the screen, but doesn't look correct for recovery

[rimasi98]

That looks like the right method now.
Can't read the screen, but doesn't look correct for recovery

The message is just a warning that is no device connected to the LCD

[P.X]

P.X here you have at i've done and the result:

https://www.youtube.com/watch?v=f3rWZd7AgG4

I also tried to short pins on the PCB and the result is allways the same:

If you are trying to do the PCB short method on the eMMC then you need to attach to computer and use USB Burn Tool I believe !?!

Best to try the USB Burn Tool and the Reset Switch Short method first.

Load USB Burn Tool.
Switch to English (Menu Bar button 2 - Item "English")
Load an IMG File
Click START
Connect USB A-A male cable (No power supply to box) while shorting RESET SW
Tool should detect Box and start a ROM Burn ......

[P.X]

RESET - if No Switch Fitted Pro L (and Pro +)

Click - Full Size
Short RED - Any Black (whichever is easiest!)

[rimasi98]

If you are trying to do the PCB short method on the eMMC then you need to attach to computer and use USB Burn Tool I believe !?!

Best to try the USB Burn Tool and the Reset Switch Short method first.

Load USB Burn Tool.
Switch to English (Menu Bar button 2 - Item "English")
Load an IMG File
Connect USB A-A male cable (No power supply to box) while shorting RESET SW
Tool should detect Box and start a ROM Burn ......

Yes i've already tried that and it doesn't pass the 2% and give an error:

http://prntscr.com/i400dl

I use the shorting on reset pins and then powered with USB male to male to the pc after i click "Start" on the UBS Burning tool with the loaded firmware

PS: if i plug also the power supply it stays at 7% when is formatting and gives me this error:

http://prntscr.com/i400uu

[P.X]

Yes i've already tried that and it doesn't pass the 2% and give an error:

http://prntscr.com/i3zvyv

I use the shorting on reset pins and then powered with USB male to male to the pc after i click "Start" on the UBS Burning tool with the loaded firmware

Should say
Click START before Connect USB - A-A in above method (EDited)

Keep Reset Shorted until Upload Starts automatically ....

[rimasi98]

RESET - if No Switch Fitted Pro L (and Pro +)

Click - Full Size

All 4??