Tried the 106k4 img and it flashed after lot of attempts. But the box refuses to switch on. It has done this a few times after a flash with different img's. This was also the reason I flashed the box in the 1st place.
-
Last edited by kPATm; 28 October 2015, 02:08. -
I have a unit that refuses to power on. It's an red/orange light and does nothing. Is this a corrupt rom issue or something else? I have not flashed any custom roms onto it, except for the update Beelink pushed through yesterday or the day before. Factory reset doing nothing.
Comment
-
Dear NanosecOriginally posted by nanosec View Post
Do you means that you had just accepted OTA update ,and then fail to boot? After accept OTA update it will download image and reboot into recovery mode to update , and then auto reboot to enter system.which step says failure as your remember ?
It seems software not works. Need an USE A-A male cable to update.
thanksComment
-
Hi kPaTm,Originally posted by kPATm View Post
with USB cable or TF card or U storage or OTA? Does the device fails during the update bar and auto reboot severy times ?
SorryComment
-
The only way I can update is via the USB cable it seems.
90% of the time I get a "Burn firmware failed" message
The box never reboots when I have a successful flash. I have to remove the power cable then try and reboot manually but that hasnt worked either?Comment
-
Thanks mate. I will try after work.Originally posted by bluesmanuk View Post
Try installing the VPN dialogues APK and try your VPN service again.
Comment
-
Has anyone had success flashing the X2 using Dragon Tough PC Tool?Comment
-
Originally posted by kPATm View Post
I was playing around with an X2 the other day and also found that after a flash using the SD card the box would invariably not power up afterwards and that I had to remove the power cable and let it stand for half an hour before it would boot up correctly.
I also encountered the burn failed message a couple of times, so it it a little hit and miss.
Flashing with the cable does work though once you go through the correct process, although sticking pins in little holes in the vase of these products is a pain at times and there should be an easier way, or at least better positioning of the reset holes.
R-TV BOX S10, Beebox N3150, Chuwi Hibox, Nvidia Shield, A95X MaxComment
-
I think I may try and flash using the method mentioned in post #78
The thing concerning me is that I cant get the box to turn on so how do I flash via Micro SD?
What write mode to you set PhoenixCard 3.1.0 at
Product, Start up, or Burn Key?Comment
-
Originally posted by kPATm View Post
What you will likely find is that if you are able to successfully create an SD card flashing image that when you pop it into the X2, it will magically come to life upon it's detection.
I found that on more then one occasion where the box didn't look as if it wanted to come to life.
R-TV BOX S10, Beebox N3150, Chuwi Hibox, Nvidia Shield, A95X MaxComment
-
Mine on my tv sometimes only works after i power off/on the tv with the box on...
But i think is better you start thinking on returning it!Comment
-
Well I used PhoenixCard and wrote the image using startup mode. With no power going to the box I inserted the Micro USB then I plugged the box in but it just stays at a red light. Its been like that for about an hour and nothing?Comment
-
I have already informed GearBest of the problem but they are pretty useless. I may open a PayPal dispute to get my money back?Comment
-
Can any of the images from here http://www.tabletexpress.com/tablet.html?brand=272&p=3
be used to flash the X2?Comment
-
Originally posted by kPATm View Post
You may well find that some of the driver components will be different and therefore find functions that do not work.
They do however have a Karaoke option in the top right hand corner where is says 'Sing in'
Either that or they have a novel new voice activated sign in option.
R-TV BOX S10, Beebox N3150, Chuwi Hibox, Nvidia Shield, A95X MaxComment
Comment