VORKE Z6 Android 7.1.2 Amlogic S912 TV BOX 3/32GB eMMC5.0 WIFI BT Gig LAN

[Jancales]

thank you very much for your interest, I still could not relive it.

the way you explain, you have to short-circuit? If so, if so, at what moment do you do it?

That is what I try to say in my latest post, you need to try all combinations, because the second box responded different from the first box.

Open USB burning tool - load the firmware and press start.

Then try different combinations like first SC - connect usb - connect power supply. Doesn't work?Next combination connect usb - SC - connect PS. Doesn't work try another combination

Take note, after each try you need to remove SC- unplug usb and power before you try the next combination.

When you short circuit you keep it short circuited.

I'm sure you will get it to work

[Deibi]

That is what I try to say in my latest post, you need to try all combinations, because the second box responded different from the first box.

Open USB burning tool - load the firmware and press start.

Then try different combinations like first SC - connect usb - connect power supply. Doesn't work?Next combination connect usb - SC - connect PS. Doesn't work try another combination

Take note, after each try you need to remove SC- unplug usb and power before you try the next combination.

When you short circuit you keep it short circuited.

I'm sure you will get it to work

thank you very much, in this way if I can connect to the computer.

but now it fails to load the firmware:

[15:47:21 646][HUB3-2][Err]--[0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error
[15:47:21 646][HUB3-2][Inf]--Close device handle 0x00000304

I already had this error before, it is only removed when I uncheck the boxes Erase flash and Erase bootloader.

that made bad firmware loaded.

any solution?

[Jancales]

thank you very much, in this way if I can connect to the computer.

but now it fails to load the firmware:

[15:47:21 646][HUB3-2][Err]--[0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error
[15:47:21 646][HUB3-2][Inf]--Close device handle 0x00000304

I already had this error before, it is only removed when I uncheck the boxes Erase flash and Erase bootloader.

that made bad firmware loaded.

any solution?

You need to check erase flash and erase bootloader.

If it gives the error just unplug the usb and plug in again. DO NOT PRESS STOP.

try different usb ports on your pc or different usb cable.

Many people have this error, but at the end it will work.

If you now know how to make usb burning tool recognise the box, you can also try restart your PC.

Do you use usb burning tool 2.0.8?

[RASTAVIPER]

guys do you tick erase bootloader when flashing firmware to this tv-box ?

update

Vorke Z6 for 60.99$ with coupon code geekbuying
Vorke Z6 Plus 50.99$ with coupon code geekbuying

plus 8% cashback https://www.expressbonus.com/en/shop...geekbuyingcom/

55$ without any coupons for Vorke Z6 plus
https://www.geekbuying.com/item/VORK...liday_20171205

[Deibi]

You need to check erase flash and erase bootloader.

If it gives the error just unplug the usb and plug in again. DO NOT PRESS STOP.

try different usb ports on your pc or different usb cable.

Many people have this error, but at the end it will work.

If you now know how to make usb burning tool recognise the box, you can also try restart your PC.

Do you use usb burning tool 2.0.8?

Yes, I'm using 2.0.8, I'm testing all the ports and nothing, I'm going to restart.

[Jancales]

Yes, I'm using 2.0.8, I'm testing all the ports and nothing, I'm going to restart.

Quality of usb cable is important. The shorter the better also.

Oh and I read somewhere, you should avoid usb 3.0

[Deibi]

Quality of usb cable is important. The shorter the better also.

Oh and I read somewhere, you should avoid usb 3.0

All your recommendations are taken into account, but I can not get more than 2%.

connected to usb 2.0, with 0.50 cm usb.
and I do not get it, this error was already before putting the firware,
we have advanced a lot, surely the solution will come soon.
I'll keep doing test.
I am tremendously grateful, you have helped me a lot.
If something else happens to him, I'll look to try.

[Jancales]

All your recommendations are taken into account, but I can not get more than 2%.

connected to usb 2.0, with 0.50 cm usb.
and I do not get it, this error was already before putting the firware,
we have advanced a lot, surely the solution will come soon.
I'll keep doing test.
I am tremendously grateful, you have helped me a lot.
If something else happens to him, I'll look to try.

I don't understand what you mean with " this error was already before putting the firmware"

You only can get an error after you have 1. loaded the firmware file in usb burning tool and 2. connected the box.

If one of both is missing the tool will not start, and you can't get an error.

Do press start in usb burning tool before you start connecting the box?

Have you tried to re-download the firmware or tried a different one?

Use the unrooted one and download it directly from Geekbuying blog.

http://blog.geekbuying.com/2017/11/vorke-z6-android-7-1-2-amlogic-s912-tv-box-firmware-update-20171116/

[Jancales]

And do not select reset after success.

[Deibi]

I don't understand what you mean with " this error was already before putting the firmware"

You only can get an error after you have 1. loaded the firmware file in usb burning tool and 2. connected the box.

If one of both is missing the tool will not start, and you can't get an error.

Do press start in usb burning tool before you start connecting the box?

Have you tried to re-download the firmware or tried a different one?

Use the unrooted one and download it directly from Geekbuying blog.

http://blog.geekbuying.com/2017/11/v...date-20171116/

look at this photo

http://c2n.me/3Q5iH5P

[Deibi]

I don't understand what you mean with " this error was already before putting the firmware"

You only can get an error after you have 1. loaded the firmware file in usb burning tool and 2. connected the box.

If one of both is missing the tool will not start, and you can't get an error.

Do press start in usb burning tool before you start connecting the box?

Have you tried to re-download the firmware or tried a different one?

Use the unrooted one and download it directly from Geekbuying blog.

http://blog.geekbuying.com/2017/11/v...date-20171116/

all that tells me is tried, must have a problem in OTG

I have tried from another PC and it gives the same problem

this error has always happened, I read this post to install the firmware.
[url]https://forum.xda-developers.com/android-stick--console-computers/amlogic/usbburningtool-error-t3321735/page2[url]


that way I did not get an error, but not recorded well.

[Jancales]

all that tells me is tried, must have a problem in OTG

I have tried from another PC and it gives the same problem

this error has always happened, I read this post to install the firmware.
[url]https://forum.xda-developers.com/android-stick--console-computers/amlogic/usbburningtool-error-t3321735/page2[url]


that way I did not get an error, but not recorded well.

What you mean with " that way I did not get an error, but not recorded well." ?

As you can see from the thread you quoted, all those involved succeeded somehow, so you need to keep trying and make sure you have a good quality usb cable.

[Deibi]

What you mean with " that way I did not get an error, but not recorded well." ?

As you can see from the thread you quoted, all those involved succeeded somehow, so you need to keep trying and make sure you have a good quality usb cable.

by unchecking the boxes, erase flash and erase bootloader, 100% complete the process and no longer starts more.

from there is only the blue button turns on.

Now it does not work even if you uncheck the boxes.

[Deibi]

I have good news, I managed to install the firmware.
For those who have Vorke Z6 plus, ¡firmwares or roms are not compatible with Z6!.

This was the whole problem.

by chance install the firmware tanix Tx9 pro, and it loaded to the first, my vox tv reborn.

A thousand thanks Jancales, without your help I would not have been able.

I leave the firmware link in case someone needs it

[Jancales]

I have good news, I managed to install the firmware.
For those who have Vorke Z6 plus, ¡firmwares or roms are not compatible with Z6!.

This was the whole problem.

by chance install the firmware tanix Tx9 pro, and it loaded to the first, my vox tv reborn.

A thousand thanks Jancales, without your help I would not have been able.

I leave the firmware link in case someone needs it

You mean you have a Z6 Plus DDR3 and all the time you were trying to flash a firmware for the Z6 DDR4 ?

Anyone could have told you that from the first day, why you didn't mention it?

There is by the way firmware for the Z6 Plus on the official website.

http://www.vorke.com/download++center