UPDATED - CX919 - 4.2.2 - Finless ROM 1.6b

[FadeFx]

Re: UPDATED - CX919 - 4.2.2 - Finless ROM 1.6b

which is the otg port? if its the side it never shows up only the main one shows in win.

It is marked as otg usually. But it should be the side port iirc.

If the flashtool finds it you should be good to go actually.

_________________________
tapatalked from GalaxyS3

[ilovemymac]

It is marked as otg usually. But it should be the side port iirc.

If the flashtool finds it you should be good to go actually.

_________________________
tapatalked from GalaxyS3

It says DC on here.
ANd i cant be good to go it wont let me reboot to flash.

Also how to you swap out the 720 for the 1080P kernel?

[FadeFx]

Re: UPDATED - CX919 - 4.2.2 - Finless ROM 1.6b

It says DC on here.
ANd i cant be good to go it wont let me reboot to flash.

Dc is the wrong one. And you don't need to reboot to flash. Just DISCONNECT ALL cables from the device, hold the button on the off device while connecting the otg port to your pc. When it starts up it will be in flash mode.

_________________________
tapatalked from GalaxyS3

[ilovemymac]

Dc is the wrong one. And you don't need to reboot to flash. Just DISCONNECT ALL cables from the device, hold the button on the off device while connecting the otg port to your pc. When it starts up it will be in flash mode.

_________________________
tapatalked from GalaxyS3

ok so how to i put the 1080P rom because it says 720 on the kernel

[FadeFx]

Re: UPDATED - CX919 - 4.2.2 - Finless ROM 1.6b

ok so how to i put the 1080P rom because it says 720 on the kernel

Just double click the filename and replace the 720 by 1080 in it. Then do the same for the bootloader.

_________________________
tapatalked from GalaxyS3

[FadeFx]

AW: UPDATED - CX919 - 4.2.2 - Finless ROM 1.6b

ok so how to i put the 1080P rom because it says 720 on the kernel

I assume you managed to flash it now... thanx... ;-)

_________________________
tapatalked from GalaxyS3

[rudik7777777]

help

so how to solve the problem by flashing the screen flashes every 1-3 seconds? Please help, tried all the kernel that does not work, even on Runoff firmware now blinking (((

[louser]

Driver Isssue

Hey all,

Ben running 1.4 rom and its been great. I wanted to update the rom and im running into driver issues. I cant get my driver to update and im stuck. I attached a pic, could anyone help?

[smithmal]

More thorough explanation of my findings with this build are noted in this post, however I wanted to mention my 1.6b findings in the main build thread.

My stick for some reason can not use any of the kernels for this build (1.6b) nor 1.5 (when flashing with these kernels I got a "No HDMI" signal). In order to properly flash this build I needed to switch out the kernel to the one contained in the 1.4 build. Also, the recovery console for 1.6b or 1.5 would not show during the flash. It did show if I replaced it with the one packed in the 1.4 build.

So, what I have is a stick using all the components of the 1.6b build except the kernel and recovery console (both of which come from the 1.4 build).

Finally, I really like the mods that Nomad13 provided in his earlier post. They are working great on my stick. I'm glad I finally got this dang thing working again. It's been a real pain trying to figure out why I was having all my issues.

smithmal

[smithmal]

Hey all,

Ben running 1.4 rom and its been great. I wanted to update the rom and im running into driver issues. I cant get my driver to update and im stuck. I attached a pic, could anyone help?

Does the flash tool recognize your stick when you put it into flash mode when connecting it to the PC? If so, I wouldn't worry about the drivers. I notice issues with my PC not recognizing my stick constantly, but what really matters (in terms of being able to flash ROMs and firmwares) is if the flash tool recognizes the stick after you put the stick into flash mode.

smithmal

[rudik7777777]

help

Who did a backup of the firmware,cast on some exchanger, 'll be very grateful +++ with me.

[JugsteR]

Re: UPDATED - CX919 - 4.2.2 - Finless ROM 1.6b

Who did a backup of the firmware,cast on some exchanger, 'll be very grateful +++ with me.

What does this mean? Some More information please. And no need to tell us english isn't your native English. That much was understood.


Signature? Signature!

[peety]

Dump

What does this mean? Some More information please. And no need to tell us english isn't your native English. That much was understood.


Signature? Signature!

Sounds like he is asking if anyone did a dump of the original rom and has it on a server somewhere? I think you meant to say native language?

[rudik7777777]

What does this mean? Some More information please. And no need to tell us english isn't your native English. That much was understood.


Signature? Signature!

When flashing on 1.6b with factory(stock) to blink on the screen of the TV,I've tried all of the kernel none came. I want to go back to factory firmware. And the stock firmware that is on the site also blink.

[rudik7777777]

Sounds like he is asking if anyone did a dump of the original rom and has it on a server somewhere? I think you meant to say native language?

I'm from Russia, translate with a dictionary, if that sorry.