[ROM] Android TV (7.1.2) Beelink GT1 (Multi 6255 & 9377 Standard+Ultimate)

[Clayman_32]

try this the 2gb dtb has ram config for 3gb [ATTACH]n708106[/ATTACH] flash in recovery

this might actually only work in a burn image though like when i re-partitioned the system, let me know 706D only

I will try in the afternoon and post the result ️

[Winno]

try this the 2gb dtb has ram config for 3gb [ATTACH]n708106[/ATTACH] flash in recovery

this might actually only work in a burn image though like when i re-partitioned the system, let me know 706D only

No luck.

Saw *** Start *** and "Done.".

There was the message
E: [] Unknown Command

Which was show when trying to show the return value

After the flash the box powered off and didn't reboot - no light on the front. Pulled the power cord and put it back in, light on but still didn't boot.

Will flash back to V10
I

[tillaz87]

No luck.

Saw *** Start *** and "Done.".

There was the message
E: [] Unknown Command

Which was show when trying to show the return value

After the flash the box powered off and didn't reboot - no light on the front. Pulled the power cord and put it back in, light on but still didn't boot.

Will flash back to V10

Might need done with a burn image like the system re-partition as the ram would also need to be re-partitioned
as this bug is having it set as 2gb at boot

I can test my self with 1gb config actually will see if I can get my box locked to 1gb ram then should know if it's just needs done with burn in mage.

[Winno]

Might need done with a burn image like the system re-partition as the ram would also need to be re-partitioned
as this bug is having it set as 2gb at boot

I can test my self with 1gb config actually will see if I can get my box locked to 1gb ram then should know if it's just needs done with burn in mage.

Good idea...

As you can see from my multiple edits I'm pissing in the wind a bit with this as I haven't done anything with Android before.
Can you share some insights on the tools you use? Would be good to be a little self sufficient.

[Alexei95]

Might need done with a burn image like the system re-partition as the ram would also need to be re-partitioned
as this bug is having it set as 2gb at boot

I can test my self with 1gb config actually will see if I can get my box locked to 1gb ram then should know if it's just needs done with burn in mage.

Hey tillaz87

Do you know if the new firmware GT1_ULTIMATE_3GB_32G - GT1_707D0_AP6255 have the same problem (http://www.bee-link.com/Beelink-28438-1-1.html)
I want to go on your Rom Android TV but as usual, i prepare a rollback because there is so problem on doing this (brick, lag, problem...)

By the way, thank you for all your work and the ADB over Ethernet/wifi tip because i was stuck on it

Cheers

[tillaz87]

Hey tillaz87

Do you know if the new firmware GT1_ULTIMATE_3GB_32G - GT1_707D0_AP6255 have the same problem (http://www.bee-link.com/Beelink-28438-1-1.html)
I want to go on your Rom Android TV but as usual, i prepare a rollback because there is so problem on doing this (brick, lag, problem...)

By the way, thank you for all your work and the ADB over Ethernet/wifi tip because i was stuck on it

Cheers

no, its ok on stock

[tillaz87]

Good idea...

As you can see from my multiple edits I'm pissing in the wind a bit with this as I haven't done anything with Android before.
Can you share some insights on the tools you use? Would be good to be a little self sufficient.

No luck with this any change to ram size in the dtb wont boot even with burn image

3GB code 0xbff00000 which is hex for 3220176896

    memory@00000000 {
        device_type = "memory";
        linux,usable-memory = <0x0 0x100000 0x0 0xbff00000>;
    };

2GB code 0x7ff00000 which is hex for 2146435072

    memory@00000000 {
        device_type = "memory";
        linux,usable-memory = <0x0 0x100000 0x0 0x7ff00000>;
    };

[CHARLUS60]

Hello I installed the latest updates for my gt1 ultimate ax12 I started with the latest 20180119 [ROM] Beelink GT1 / Alfawise S92 TVStock Nexus ROM (Android TV 7.1). But despite a nice interface I still have concerns about the sound dolby or dts that are not decoded when I use plex or netflix, by cons if I read a video file (mkv) directly it works. So I installed the latest v10 [ROM] Android TV (7.1.2) Beelink GT1 (Multi 6255 & 9377 Standard + Ultimate) Same problem. On this rom it worked with the v8 Do you have a solution (settings) or should I go back to v8 In addition I must reactivate the wifi at each restart of the gt1 Thank you for your answer Charles

[Don_Pachuco]

It has an ethernet port for a reason. Why use wifi? No one with a decent home network uses wifi on a device unless completely necessary.

[tillaz87]

ChangeLog V10.1:

• Fix mouse pointer size (vorke)
• Performance and thermal improvements
• Mali GPU module updated
• zygoteinit changes AOSP
• Missing DRM library's (L3)
• Audio stream stuff

[tenoce]

ChangeLog V10.1:

• Fix mouse pointer size (vorke)
• Performance and thermal improvements
• Mali GPU module updated
• zygoteinit changes AOSP
• Missing DRM library's (L3)
• Audio stream stuff

Great! Will flash it tomorrow morning. 

[Winno]

No luck with this any change to ram size in the dtb wont boot even with burn image

3GB code 0xbff00000 which is hex for 3220176896

 memory@00000000 {
device_type = "memory";
linux,usable-memory = <0x0 0x100000 0x0 0xbff00000>;
};

2GB code 0x7ff00000 which is hex for 2146435072

 memory@00000000 {
device_type = "memory";
linux,usable-memory = <0x0 0x100000 0x0 0x7ff00000>;
};

Bugger!

I did notice the DTB in your patch is about 10K smaller than the ones I extracted.
Fancy trying with the DTB from libreelec? https://kszaq.libreelec.tv/s912/8.2/...Gbit_Ethernet/ these are also 10K larger

[tillaz87]

Bugger!

I did notice the DTB in your patch is about 10K smaller than the ones I extracted.
Fancy trying with the DTB from libreelec? https://kszaq.libreelec.tv/s912/8.2/...Gbit_Ethernet/ these are also 10K larger

Device tree needs to match up with bootloader and boot.img it wouldn't work, mine is smaller because I removed LED stuff for the vorke z6 that the GT1 does not have as well as changing partition table for system to give more to data

[tillaz87]

Bugger!

I did notice the DTB in your patch is about 10K smaller than the ones I extracted.
Fancy trying with the DTB from libreelec? https://kszaq.libreelec.tv/s912/8.2/...Gbit_Ethernet/ these are also 10K larger

Give this a try

[Winno]

Give this a try

Nope..

Seemed to flash OK, but still had the E: [] Unknown Command error at the end
Rebooted but stuck on the Google animation. Pulled power and tried again, but still sticking at animation
At least it booted this time.