Modded ROM's for Tronsmart R68 "Tronsplant your ROM"

[lonix]

Hi :
According to dowload as below , Could you provide the other space ? Because I could not download and always show error.
Download Here v6 ----> Full ROM
Thanks.

download here from Google Drive

[reksio34]

I built this kernel with ap6330 set as wifi and set in device tree also please test it, flash with TWRP on v6

download here

Ill post it to the main page once i can confirm it works

Hi Ionix,
Same issue, no Wifi, no BT
I have a V6 ROM and AP6330 module !

[lonix]

Hi Ionix,
Same issue, no Wifi, no BT
I have a V6 ROM and AP6330 module !

OK, Im going to try something else.

[lonix]

Hi Ionix,
Same issue, no Wifi, no BT
I have a V6 ROM and AP6330 module !

ok, try this,

flash back to original kernel download here

then flash this update

That should work, fingers crossed

would be easier to test if i had an i68

[natzen]

@ionix possible to patch kernel x6 to insecure ?

Write access to the system partition is usually blocked by the stock kernel at boot. i need to flash a modified kernel to be able to obtain write access to /system with adb for hdmi state patch .

[lonix]

@ionix possible to patch kernel x6 to insecure ?

Write access to the system partition is usually blocked by the stock kernel at boot. i need to flash a modified kernel to be able to obtain write access to /system with adb for hdmi state patch .

Try this

adb root
adb remount

This will allow writes to system
I can change it to insecure in the initrd if you like

Can you explain this hdmi state patch to me further, the site you referenced was in korean i dont understand

Do you need writes during early boot?

[lonix]

@ionix possible to patch kernel x6 to insecure ?

Write access to the system partition is usually blocked by the stock kernel at boot. i need to flash a modified kernel to be able to obtain write access to /system with adb for hdmi state patch .

UPDATE

have modified kernel to always report 0 for /sys/devices/virtual/switch/hdmi/state // this was easy
now I just need to take care of /sys/class/display/HDMI/connected //ok this was easy too

seem's that some apps are looking beyond these two variables for example the "stan" app in australia

ok here it is, https://mega.nz/#!XcIGVKBC!g9KsetZlz...MrtHNkuGJHZvLA

this has
/sys/devices/virtual/switch/hdmi/state = 0
and
/sys/class/display/HDMI/connected = 0

[mo123]

UPDATE

have modified kernel to always report 0 for /sys/devices/virtual/switch/hdmi/state // this was easy
now I just need to take care of /sys/class/display/HDMI/connected //ok this was easy too

seem's that some apps are looking beyond these two variables for example the "stan" app in australia

Hi
Can you test HBO Go, HBO Now, not sure which app has free streams to test.
It said something about 'external display connected'

[reksio34]

ok, try this,

flash back to original kernel download here

then flash this update

That should work, fingers crossed

would be easier to test if i had an i68

Hi Ionix,

Same issue

[lonix]

Hi
Can you test HBO Go, HBO Now, not sure which app has free streams to test.
It said something about 'external display connected'

I have'nt tested those apps yet as I need a VPN to get access, I did have some success with "Stan" which is a video streaming service similar to netflix,
before i would just get a black screen, now i get a picture but it flickers black, as if the variable is constantly changing

[axionflow]

Ionix:

I have followed your work, but I have a box that I could not take advantage.

It is possible both

1.The Zido launcher, work in firmware 201L tronsmart

2. DRM, Widevine L3 support.

I do not know if other people have noticed, but my case is all time my box is hot.

Honestly, I'm tired of the shortcomings of this box.

Programmers like you have my respect.

Go back to the original firmware and try to ignore the stuttering.

Overclocking can burn my processor

Thank you

[lonix]

Ionix:

I have followed your work, but I have a box that I could not take advantage.

It is possible both

1.The Zido launcher, work in firmware 201L tronsmart

2. DRM, Widevine L3 support.

I do not know if other people have noticed, but my case is all time my box is hot.

Honestly, I'm tired of the shortcomings of this box.

Programmers like you have my respect.

Go back to the original firmware and try to ignore the stuttering.

Overclocking can burn my processor

Thank you

1. The Zidoo launcher is deeply ingrained into the framework so i cant bring it across, ive tried.
2. This is definately possible

If your box runs too hot, you can use the standard kernel

[natzen]

UPDATE

have modified kernel to always report 0 for /sys/devices/virtual/switch/hdmi/state // this was easy
now I just need to take care of /sys/class/display/HDMI/connected //ok this was easy too

seem's that some apps are looking beyond these two variables for example the "stan" app in australia

ok here it is, https://mega.nz/#!XcIGVKBC!g9KsetZlz...MrtHNkuGJHZvLA

this has
/sys/devices/virtual/switch/hdmi/state = 0
and
/sys/class/display/HDMI/connected = 0

very good , i have zidoo 1.0.27 ,it's good for me ? or i update to 1.0.30 before ?

and i patch just kernel or boot ,kernel and ressource ?

[mo123]

very good , i have zidoo 1.0.27 ,it's good for me ? or i update to 1.0.30 before ?

and i patch just kernel or boot ,kernel and ressource ?

You have to use it with the firmware in the first post here

https://mega.nz/#!DIhgjIJK!h3j4BZK0qmate14ScmeAqf_8gs5w2hj4a_PN1NbGe1w

[natzen]

mo123 sure ? my box is original zidoo x6 pro ,this firmware compatible ?